Lexmark Optra RN+

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If this is the first time a Service Fuser error has appeared on the printer, power it off. Wait ten seconds, and then power the printer on again. The printer should come up to the Ready state. If it does, try printing again.
The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.
The fuser unit or fuser is a critical part of any laser printer. Using pressure and heat, it fuses the toner powder onto the page to create a print, and without it, the printer cannot operate.
Streaking, smudging, black lines, and double images are all symptoms of a bad fuser. When you notice these printing defects and experience problems, such as paper jams or wrinkles, this is a good sign to replace the fuser kit.
Fuser Units

The coating wears off and causes the toner to not fuse properly. There are replacement rollers and sleeves on the market that you can replace and turn a non-functional fuser into a good working one. Rebuilding fuser assemblies is not a new thing.

The fuser unit must be replaced every 100,000 pages, usually along with the transfer belt and feed rollers as part of a maintenance kit. The error code 010-351 indicates that the fuser has reached 75,000 pages and as a result has 25% life or less remaining.
A component found in electrostatic printers, laser printers, and xerographic printers and photocopiers. The fuser unit is used to permanently bond toner to a substrate by applying heat and pressure. A fuser unit is made up of two rollers; one to apply heat and one to apply pressure.
Your printer monitors the life of your fuser. When the fuser reaches the end of its life, the printer displays 80 Fuser Exhausted. This message indicates it is time for you to replace the fuser. For best print quality, make sure you replace the fuser when the printer displays 80 Fuser Life Warning.
Restart your printer. In some cases, a simple restart can fix the issue. Unplug the printer and check if there is any paper stuck in the machine, and if the toner is installed correctly. If all seems fine leave the printer disconnected for half a minute, then reconnect it and resume the print job.
Streaking, smudging, black lines, and double images are all symptoms of a bad fuser. When you notice these printing defects and experience problems, such as paper jams or wrinkles, this is a good sign to replace the fuser kit.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :

Lexmark Optra RN+

info on refilling lexmark 16 cartridges?
ANSWER : Our proven track record includes 20 million cartridges sold since 2004, saving $180 million for our customers who would have otherwise bought new cartridges. Unlike many discount cartridge resellers, Inkplicity is a manufacturer, instead of only a distributor mail order firm. By eliminating the wholesaler and maintaining complete control of our cartridges from product design and development to your doorstep, Inkplicity continuously delivers extraordinary savings and quality to you. For more info -Refilled Cartridges

Read Full Q/A … :

Lexmark Optra RN+

Restore settings Lexmark x466
ANSWER : Try this:

Read Full Q/A … :

Lexmark Optra RN+

Lexmark Printer Problems
ANSWER : lexmark printers can be fixed . just follow the steps . uninstall the printer and drivers and install the printer driver and setup again from lexmark and than make sure you internet password and you are all set to go for more visit http://lexmark.technical-care.com/ and i hope this will help you . thanks

Read Full Q/A … :

Lexmark Optra RN+

Lexmark X466 empty tray
ANSWER : The “Load Tray 1 with A4 paper” means the printer is looking for A4 size paper in Tray 1 and that is not what it is detecting. You need to make sure that the paper size that is in the tray matches what the printer is expecting so it understands that it should be looking for a specific size of paper. If you are printing on regular Letter size paper – set the printer tray to Letter instead of A4 and message should go away.

Read Full Q/A … :

Lexmark Optra RN+

Lexmark paper feed problems
ANSWER : On my X204n Lexmark laser printer, it was doing the same thing you described – basically sounded like it was trying to pick up the paper from the tray and then failing after several seconds. When you’d open the paper tray, the paper looked like it had been partially taken up with some black scuff marks on the paper that lined up with the rollers that take up the paper. I inspected the rollers and although they looked a bit smooth and worn, didn’t seem like they should be a problem. However, this particular model has just a rubber tire almost like a car tire – the rubber can come off the hard plastic wheel on the inner portion. So I popped off the two rubber “tires”, turned them inside out and put them back on. When turned inside out, the rubber looked nice and … rubbery and had a lot more grippy feeling to them. The very first printing attempt after that and the paper sucked up perfectly with no problems. I think the problem is solved! So if you have similar “tires” that take up the paper, try flipping them and see if it works for you too.

Read Full Q/A … :

Lexmark Optra RN+

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :

Lexmark Optra RN+

Lexmark T654dn power supply problem
ANSWER : Maybe this Thread may be of use:

Read Full Q/A … :

Lexmark Optra RN+