Lexmark Optra T
Experienced technical support provide their insights in answering this question :
On my X204n Lexmark laser printer, it was doing the same thing you described – basically sounded like it was trying to pick up the paper from the tray and then failing after several seconds. When you’d open the paper tray, the paper looked like it had been partially taken up with some black scuff marks on the paper that lined up with the rollers that take up the paper. I inspected the rollers and although they looked a bit smooth and worn, didn’t seem like they should be a problem. However, this particular model has just a rubber tire almost like a car tire – the rubber can come off the hard plastic wheel on the inner portion. So I popped off the two rubber “tires”, turned them inside out and put them back on. When turned inside out, the rubber looked nice and … rubbery and had a lot more grippy feeling to them. The very first printing attempt after that and the paper sucked up perfectly with no problems. I think the problem is solved! So if you have similar “tires” that take up the paper, try flipping them and see if it works for you too.
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Updated: 04/26/2017 by Computer Hope. Function of a computer printer that enables it to automatically insert paper through it, allowing it to print.
If there is paper in the tray but the printer is not picking the paper, open the tray and flip the paper stack over. Load a fresh ream of paper and observe whether the issue remains. If the issue persists, remove the whole tray out and inspect the bottom of the tray for any paper debris or obstructions.
A paper feed issue can occur for several reasons, such as dusty or contaminated paper rollers, the condition of the paper in the tray, or even issues with the software. To resolve the issue, try each solution in this document, and then use the steps in this section to print a self-test report.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust.
A paper feed issue can occur for several reasons, such as dusty or contaminated paper rollers, the condition of the paper in the tray, or even issues with the software.
“Manual Feed” is an indication that your machine`s Tray Setting or the paper source in the printer driver has been set to Manual Feed, but there`s no paper loaded in the manual feed slot.
Your 3D printer works by feeding a plastic filament into the heater core of the Extruder. The plastic melts and is then forced through the Extruder`s nozzle and applied to the worktable to print three dimensional objects.
Continuous form feed and friction feed are the two types of paper feeder mechanisms. Dot matrix printers use continuous form feed, and laser printers use friction feed.
A paper feed issue can occur for several reasons, such as dusty or contaminated paper rollers, the condition of the paper in the tray, or even issues with the software.
If your printer keeps jamming, you should know that the most common cause of a jam is misalignment of the paper. Paper needs to load in smoothly, completely flush with the tray. Overfilling the tray is a great way to ensure you will be spending some personal time getting to know the inside of a printer.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.
Read Full Q/A … :
Lexmark Optra T
Lexmark paper feed problems
ANSWER : On my X204n Lexmark laser printer, it was doing the same thing you described – basically sounded like it was trying to pick up the paper from the tray and then failing after several seconds. When you’d open the paper tray, the paper looked like it had been partially taken up with some black scuff marks on the paper that lined up with the rollers that take up the paper. I inspected the rollers and although they looked a bit smooth and worn, didn’t seem like they should be a problem. However, this particular model has just a rubber tire almost like a car tire – the rubber can come off the hard plastic wheel on the inner portion. So I popped off the two rubber “tires”, turned them inside out and put them back on. When turned inside out, the rubber looked nice and … rubbery and had a lot more grippy feeling to them. The very first printing attempt after that and the paper sucked up perfectly with no problems. I think the problem is solved! So if you have similar “tires” that take up the paper, try flipping them and see if it works for you too.
Read Full Q/A … :
Lexmark Optra T
Lexmark T654dn power supply problem
ANSWER : Maybe this Thread may be of use:
Read Full Q/A … :
Lexmark Optra T
Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.
Read Full Q/A … :
Lexmark Optra T
Tray 1 (upper tray) paper feed problem
ANSWER : There is no way of adjusting the distance of lift. Could be that the pickup roller is worn enough that it will pick up a sheet that is higher, but not one that is lower down. You can look at the end of the roller that first makes contact and see if it is worn smooth.
Read Full Q/A … :
Lexmark Optra T
Lexmark Printer Problems
ANSWER : lexmark printers can be fixed . just follow the steps . uninstall the printer and drivers and install the printer driver and setup again from lexmark and than make sure you internet password and you are all set to go for more visit http://lexmark.technical-care.com/ and i hope this will help you . thanks
Read Full Q/A … :
Lexmark Optra T
Paper Feed Problem on HP R80
ANSWER : In the last examination it is our origination of death which chooses our responses to all the inquiries life puts to us. The most pleasant spot to be is in somebody’s idea; the most secure spot to be is in somebody’s petitions.
Read Full Q/A … :
Lexmark Optra T
HP DeskJet 722C Paper Feed Problem
ANSWER : Detach the force string from the holding nothing back one and expel all paper from it.
Read Full Q/A … :
Lexmark Optra T