Lexmark Optra S
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Restart your printer. In some cases, a simple restart can fix the issue. Unplug the printer and check if there is any paper stuck in the machine, and if the toner is installed correctly. If all seems fine leave the printer disconnected for half a minute, then reconnect it and resume the print job.
If this is the first time a Service Fuser error has appeared on the printer, power it off. Wait ten seconds, and then power the printer on again. The printer should come up to the Ready state. If it does, try printing again.
Make sure that the printer is on the same network with the computer. Make sure that you are using a known working Ethernet cable. Make sure that the Ethernet cable is connected at the back of the printer to the network router, switch, or other network source to which the computer is also connected.
If the toner cartridge is replaced and the `Toner Low` message remains, the printer must be reset. To do so, power off the printer. Let it sit 20 to 40 seconds, then power it back on. If the `Toner Low` message does not appear on power-up, try printing again.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.
Your computer may not be properly connected to the printer. Perform the setup procedure described in the Setup sheet. The interface cable may not be plugged in securely. Check both ends of the interface cable between the printer and the computer.
As a general rule, when a printer runs out of ink or toner, it stops printing legibly. Depending on the printer model, the unit may look to replace one colour with another. For example, if you run out of black ink, your printer could replace it with blue, in order to still print the document you need.
Place the smart chip against the pins on the reset device. A red light will flash to show you that the chip is engaged. When the light turns green, usually six or seven seconds later, the cartridge chip is reset and ready to use.
An E9 error occurs when the printer detects that ink system maintenance is required. An Ink System Maintenance page prints containing instructions to open and close the printhead access door to resolve the error.
1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.
a misprint or misspelling in a text.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Restore settings Lexmark x466
ANSWER : Try this:
info on refilling lexmark 16 cartridges?
ANSWER : Our proven track record includes 20 million cartridges sold since 2004, saving $180 million for our customers who would have otherwise bought new cartridges. Unlike many discount cartridge resellers, Inkplicity is a manufacturer, instead of only a distributor mail order firm. By eliminating the wholesaler and maintaining complete control of our cartridges from product design and development to your doorstep, Inkplicity continuously delivers extraordinary savings and quality to you. For more info -Refilled Cartridges
Lexmark Printer Problems
ANSWER : lexmark printers can be fixed . just follow the steps . uninstall the printer and drivers and install the printer driver and setup again from lexmark and than make sure you internet password and you are all set to go for more visit http://lexmark.technical-care.com/ and i hope this will help you . thanks
Lexmark X4650 paper Jamming!!
ANSWER : Well I had two printers that had similar issues – misalignment of paper feed which rendered both printers useless. I shook the Lexmark x4650 a couple of times and then plugged it in and got new paper and voila the misalignment was gone and it actually fed paper like it used to and printed it too.
Lexmark paper feed problems
ANSWER : On my X204n Lexmark laser printer, it was doing the same thing you described – basically sounded like it was trying to pick up the paper from the tray and then failing after several seconds. When you’d open the paper tray, the paper looked like it had been partially taken up with some black scuff marks on the paper that lined up with the rollers that take up the paper. I inspected the rollers and although they looked a bit smooth and worn, didn’t seem like they should be a problem. However, this particular model has just a rubber tire almost like a car tire – the rubber can come off the hard plastic wheel on the inner portion. So I popped off the two rubber “tires”, turned them inside out and put them back on. When turned inside out, the rubber looked nice and … rubbery and had a lot more grippy feeling to them. The very first printing attempt after that and the paper sucked up perfectly with no problems. I think the problem is solved! So if you have similar “tires” that take up the paper, try flipping them and see if it works for you too.
Toner not transferring
ANSWER : What mostly goes bad in toner cartridges is the drum wiper blade. They deteriorate in new sealed cartridges. Toner caking up, not so much.
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Lexmark X466 empty tray
ANSWER : The “Load Tray 1 with A4 paper” means the printer is looking for A4 size paper in Tray 1 and that is not what it is detecting. You need to make sure that the paper size that is in the tray matches what the printer is expecting so it understands that it should be looking for a specific size of paper. If you are printing on regular Letter size paper – set the printer tray to Letter instead of A4 and message should go away.