Lexmark Optra RX+
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
If this is the first time a Service Fuser error has appeared on the printer, power it off. Wait ten seconds, and then power the printer on again. The printer should come up to the Ready state. If it does, try printing again.
The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.
A fuser unit is a pair of heated rollers within the printer that fuses the toner onto the paper being printed on. Toner particles are pulled to the paper to create the desired text and images as the paper passes the imaging drum.
Explanation. This type of error message indicates that the fuser unit inside the printer is operating below the proper temperature. If this is the first time you have seen the error.
Fuser Units
The coating wears off and causes the toner to not fuse properly. There are replacement rollers and sleeves on the market that you can replace and turn a non-functional fuser into a good working one. Rebuilding fuser assemblies is not a new thing.
A component found in electrostatic printers, laser printers, and xerographic printers and photocopiers. The fuser unit is used to permanently bond toner to a substrate by applying heat and pressure. A fuser unit is made up of two rollers; one to apply heat and one to apply pressure.
Issue description
Thus, the 121.32 fuser error can occur if the ambient temperature is below freezing. For best printer performance, it is advisable to keep the printers in a supported environment with: 60°F to 90°F temperature range. 8% to 80% relative humidity.
The printer continuously shows the 120.09 Error after installing a brand new Fuser. The following reasons may have caused the printer to post the error: Damaged Fuser connector pins. Possible damage to machine side auto-connect.
From the home screen, touch Settings > Device > Maintenance > Configuration Menu > Supply Usage And Counters. Select Fuser Reset or ITM Reset.
Issue description
The error may be due to a poor voltage line (power strip or overloaded circuit). The most common error codes that may appear on the printer display are: 121.12A.
Explanation. This type of error message indicates that the fuser unit inside the printer is operating below the proper temperature. If this is the first time you have seen the error.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Lexmark X4650 paper Jamming!!
ANSWER : Well I had two printers that had similar issues – misalignment of paper feed which rendered both printers useless. I shook the Lexmark x4650 a couple of times and then plugged it in and got new paper and voila the misalignment was gone and it actually fed paper like it used to and printed it too.
Read Full Q/A … :
Lexmark Optra RX+
Restore settings Lexmark x466
ANSWER : Try this:
Read Full Q/A … :
Lexmark Optra RX+
info on refilling lexmark 16 cartridges?
ANSWER : Our proven track record includes 20 million cartridges sold since 2004, saving $180 million for our customers who would have otherwise bought new cartridges. Unlike many discount cartridge resellers, Inkplicity is a manufacturer, instead of only a distributor mail order firm. By eliminating the wholesaler and maintaining complete control of our cartridges from product design and development to your doorstep, Inkplicity continuously delivers extraordinary savings and quality to you. For more info -Refilled Cartridges
Read Full Q/A … :
Lexmark Optra RX+
Lexmark Printer Problems
ANSWER : lexmark printers can be fixed . just follow the steps . uninstall the printer and drivers and install the printer driver and setup again from lexmark and than make sure you internet password and you are all set to go for more visit http://lexmark.technical-care.com/ and i hope this will help you . thanks
Read Full Q/A … :
Lexmark Optra RX+
Lexmark paper feed problems
ANSWER : On my X204n Lexmark laser printer, it was doing the same thing you described – basically sounded like it was trying to pick up the paper from the tray and then failing after several seconds. When you’d open the paper tray, the paper looked like it had been partially taken up with some black scuff marks on the paper that lined up with the rollers that take up the paper. I inspected the rollers and although they looked a bit smooth and worn, didn’t seem like they should be a problem. However, this particular model has just a rubber tire almost like a car tire – the rubber can come off the hard plastic wheel on the inner portion. So I popped off the two rubber “tires”, turned them inside out and put them back on. When turned inside out, the rubber looked nice and … rubbery and had a lot more grippy feeling to them. The very first printing attempt after that and the paper sucked up perfectly with no problems. I think the problem is solved! So if you have similar “tires” that take up the paper, try flipping them and see if it works for you too.
Read Full Q/A … :
Lexmark Optra RX+
Lexmark X466 empty tray
ANSWER : The “Load Tray 1 with A4 paper” means the printer is looking for A4 size paper in Tray 1 and that is not what it is detecting. You need to make sure that the paper size that is in the tray matches what the printer is expecting so it understands that it should be looking for a specific size of paper. If you are printing on regular Letter size paper – set the printer tray to Letter instead of A4 and message should go away.
Read Full Q/A … :
Lexmark Optra RX+
Inkjet Cartridges and Toner Refilling Instructions
ANSWER : Step 1: What you require. Printer-ink. You can purchase it from a PC store. …
Read Full Q/A … :
Lexmark Optra RX+
HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply
Read Full Q/A … :
Lexmark Optra RX+