Lexmark Optra Color 1200

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Does error 900 occur while your Lexmark printer is not connected to your network or your computer? In this case, the error could be caused by a problem with the hardware or by a connection problem. To solve the issue, turn off the printer and disconnect all cables except the power cord.
In general, a 900 Service RIP error is a situation where the printer cannot process a file that has been sent. In some cases the file is corrupted and in other cases the printer`s firmware simply cannot interpret that file.
Lexmark Error Code(s): 80, 81 (Need a new maintenance kit) Error: Newer modern Lexmark printers will alert you about their maintenance, printers will usually have a limit on the number of pages they can print before they need to have a maintenance kit replaced.
A damaged or missing bin full flag, produced when a staple finisher optionis installed on the printer, causes this error to appear. above the printer exit to avoid damaging the bin full flag.
If the printer generates a 900 firmware error when connected to a data connection while there are no print jobs in any of the print queues, there may be a source on the network which is sending corrupt data which the printer cannot interpret.
Lexmark printers display the firmware error 900.00 on the printer`s control panel while the printer is functioning. This error is commonly known as firmware error. It means a network issue. The error code 900.00 occurs during a communication problem or if there is a hardware issue.
A 909 Error indicates that the MFP/printer has detected a problem with the electrical power being supplied to it and has shut down to prevent damage.
Open Fuser Thermistor Check Failure. After you remove a paper jam or upon boot-up, the printer posts a 924.01 error. The error may appear should the fuser be removed while the printer is in power saver mode, or if it has been turned on while the fuser is still detached from the printer.
The printer posts a Printhead Error (930, 931, 932, 933, 934, 935, 936) where a cable on the printer`s system board may be slightly loose. Power the printer off. Leave the printer powered off for at least one minute. Power the printer back on.
Confirm that this toner cartridge has not been refilled or reworked. If it has, try an original Lexmark cartridge. A refilled toner cartridge can trigger this error.
Power the printer off. Leave the printer powered off for at least one minute. Power the printer back on. If powering the printer off and on clears the error, continue using the printer but keep an eye on it to see if any printhead errors return.
In some cases a 900 error can mean a detection issue. This occurs when there are issues resolving the paths needed to check if patches are applicable.
Power the printer off. Leave the printer powered off for at least one minute. Power the printer back on. If powering the printer off and on clears the error, continue using the printer but keep an eye on it to see if any printhead errors return.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Lexmark printers display the firmware error 900.00 on the printer`s control panel while the printer is functioning. This error is commonly known as firmware error. It means a network issue. The error code 900.00 occurs during a communication problem or if there is a hardware issue.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Lexmark paper feed problems
ANSWER : On my X204n Lexmark laser printer, it was doing the same thing you described – basically sounded like it was trying to pick up the paper from the tray and then failing after several seconds. When you’d open the paper tray, the paper looked like it had been partially taken up with some black scuff marks on the paper that lined up with the rollers that take up the paper. I inspected the rollers and although they looked a bit smooth and worn, didn’t seem like they should be a problem. However, this particular model has just a rubber tire almost like a car tire – the rubber can come off the hard plastic wheel on the inner portion. So I popped off the two rubber “tires”, turned them inside out and put them back on. When turned inside out, the rubber looked nice and … rubbery and had a lot more grippy feeling to them. The very first printing attempt after that and the paper sucked up perfectly with no problems. I think the problem is solved! So if you have similar “tires” that take up the paper, try flipping them and see if it works for you too.

Read Full Q/A … :

Lexmark Optra Color 1200

Restore settings Lexmark x466
ANSWER : Try this:

Read Full Q/A … :

Lexmark Optra Color 1200

Lexmark Printer Problems
ANSWER : lexmark printers can be fixed . just follow the steps . uninstall the printer and drivers and install the printer driver and setup again from lexmark and than make sure you internet password and you are all set to go for more visit http://lexmark.technical-care.com/ and i hope this will help you . thanks

Read Full Q/A … :

Lexmark Optra Color 1200

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :

Lexmark Optra Color 1200

info on refilling lexmark 16 cartridges?
ANSWER : Our proven track record includes 20 million cartridges sold since 2004, saving $180 million for our customers who would have otherwise bought new cartridges. Unlike many discount cartridge resellers, Inkplicity is a manufacturer, instead of only a distributor mail order firm. By eliminating the wholesaler and maintaining complete control of our cartridges from product design and development to your doorstep, Inkplicity continuously delivers extraordinary savings and quality to you. For more info -Refilled Cartridges

Read Full Q/A … :

Lexmark Optra Color 1200

Lexmark X4650 paper Jamming!!
ANSWER : Well I had two printers that had similar issues – misalignment of paper feed which rendered both printers useless. I shook the Lexmark x4650 a couple of times and then plugged it in and got new paper and voila the misalignment was gone and it actually fed paper like it used to and printed it too.

Read Full Q/A … :

Lexmark Optra Color 1200

Error code sc27-04
ANSWER : Sorry the code is sc27-04

Read Full Q/A … :

Lexmark Optra Color 1200

Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.

Read Full Q/A … :

Lexmark Optra Color 1200