Lexmark Optra S

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Creases and folds in the paper are normally due to one of the following conditions: The paper is not correctly loaded in the paper tray. You are printing on a special type of paper or other media. The paper has absorbed too much moisture from the surrounding air.
One of the possible causes of this issue is the Exit Sensor is blocked too long and was not able to clear the sheet. Another possible cause can be a loose back door, tape on reverse solenoid pad (as shown in the image below), or a worn/contaminated Fuser.
Paper pushed too far into the input tray when it is loaded, might feed into the printer incorrectly, causing the paper to tear. Paper stacks loaded into the input tray with too many or too few sheets of paper, might feed into the printer incorrectly, causing the paper to tear.
Paper pushed too far into the input tray when it is loaded, might feed into the printer incorrectly, causing the paper to tear. Paper stacks loaded into the input tray with too many or too few sheets of paper, might feed into the printer incorrectly, causing the paper to tear.
Your printer can become misaligned if there is any paper stuck in the machine, print cartridges are clogged or dirty, improper installation of cartridges and using low quality cartridges. Additionally, a printer can become misaligned after the machine completes a large print job.
Paper pushed too far into the input tray when it is loaded, might feed into the printer incorrectly, causing the paper to tear. Paper stacks loaded into the input tray with too many or too few sheets of paper, might feed into the printer incorrectly, causing the paper to tear.
Dots are typically caused by foreign material inside the machine (for example, paper dust, glue from labels or envelopes, paper clips, staples) sticking to or damaging the surface of the drum. Toner builds up on or sticks to these areas on the drum and creates black dots on the printed pages.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

Lexmark Optra S

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :

Lexmark Optra S

Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.

Read Full Q/A … :

Lexmark Optra S

Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳

Read Full Q/A … :

Lexmark Optra S

Lexmark X4650 paper Jamming!!
ANSWER : Well I had two printers that had similar issues – misalignment of paper feed which rendered both printers useless. I shook the Lexmark x4650 a couple of times and then plugged it in and got new paper and voila the misalignment was gone and it actually fed paper like it used to and printed it too.

Read Full Q/A … :

Lexmark Optra S

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :

Lexmark Optra S

HP LaserJet 4200 paper jam fix
ANSWER : Yes, thank you! You did a thorough post! If your still hacking away at HP’printers you will know that unfortunately HP kept using that type of solenoid with the “Sticky Mess” on all of their new Equipment. I use this method almost everyday (without removing the actual solenoid). I’ve replaced so many I got carried away and now, I sell a solenoid repair kit! It’s for those people that like convenience. I provide a professional supply of perfect material with sticky back tape pre-cut to exact dimensions! All in a little kit. I have install videos, (I don’t charge for that I believe in the Do-it -Yourself approach.) Sorry for the sales pitch… but here is my link.

Read Full Q/A … :

Lexmark Optra S

Lexmark paper feed problems
ANSWER : On my X204n Lexmark laser printer, it was doing the same thing you described – basically sounded like it was trying to pick up the paper from the tray and then failing after several seconds. When you’d open the paper tray, the paper looked like it had been partially taken up with some black scuff marks on the paper that lined up with the rollers that take up the paper. I inspected the rollers and although they looked a bit smooth and worn, didn’t seem like they should be a problem. However, this particular model has just a rubber tire almost like a car tire – the rubber can come off the hard plastic wheel on the inner portion. So I popped off the two rubber “tires”, turned them inside out and put them back on. When turned inside out, the rubber looked nice and … rubbery and had a lot more grippy feeling to them. The very first printing attempt after that and the paper sucked up perfectly with no problems. I think the problem is solved! So if you have similar “tires” that take up the paper, try flipping them and see if it works for you too.

Read Full Q/A … :

Lexmark Optra S