Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

55 – Internal Communication Problem / Controller Error

Chances are this error has occurred due to a poor connection between the DC controller and the formatter.

This is a main motor startup error. In other words when the motor is supposed to turn it can not and gives the error. I have seen this with other printers and sometimes it is not the motor that is the issue.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Event ID 55 is reported if the operating system detects the file system structure on the disk is corrupt and unusable.
The 55.1 error relates to a memory error on the dc controller. Make sure the printer is plugged directly into the wall socket and not a surge protector. If the error is still there, then you need to contact hp customer care in your location to get warranty service since it would appear parts will need to be replaced.
Description: This error is primarily caused by a transfer alienation failure in which the ITB is stuck and unable to rotate, the SR9 sensor (the primary transfer roller disengagement sensor) has gone bad or the fuser drive assembly has failed.
Printer boots up to 59. F0 Error and is unable to print. This behavior may be caused by one of the following conditions: • Transfer belt is broken and cannot properly engage the internal transfer rollers. Sensor SR17 (primary transfer roller disengagement) is dirty or bad.
Check the cabling carefully, you may have damaged the Flat flexible cable that plugs into the scanner or pinched the wires that run across the front of the scanner. Also the codes are usually 52.
Look for jammed paper or debris inside the printer, and then use both hands to remove any that you find. Use both hands to remove any jammed paper or objects from the input bin. Align the cartridge with the tracks inside the printer, push in until firmly seated, and then close the toner access door.
During a print job, the ink cartridge carriage stalls in the printer, and a Carriage Jam or E3 error displays on the printer control panel.
This error has the following causes and solutions: A sequential-output mode Open statement was executed for a file that is already open. You must close a file opened for one type of sequential access before opening it for another. For example, you must close a file opened for Input before opening it for Output.
Event ID – 55

RESOLUTION: To resolve this issue, back up the volume that contains the corrupted file(s) and exclude the corrupted file(s) from the backup job. Reformat the volume, and then restore from the backup.

Look for jammed paper or debris inside the printer, and then use both hands to remove any that you find. Use both hands to remove any jammed paper or objects from the input bin. Align the cartridge with the tracks inside the printer, push in until firmly seated, and then close the toner access door.
90 or 59.00. A0 Error resulting from a registration assembly and/or paper feed assembly that is jammed/stuck.
If you see this error code 50.5 on an HP LaserJet 4200, 4240, 4250, 4300, or 4350 series printer, the fuser installed in the printer is registering as an incorrect fuser for that model printer.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

What repair needs to be done for a "50 needs repair" message on an HP Laserjet IIIP?
ANSWER : I don’t know what you mean by good toner cartridges. They haven’t been built in about 10 years, so if they are new OEMs in the box, they are guaranteed to fail. The 50 error on that printer is mostly a burned out fuser lamp. This site was sold, so as you can see, there are no more kits available.

Read Full Q/A … :
Unknown Printer

HP Laserjet M3035xs error 13.17.00
ANSWER : If the misstep thinks of no interface join connected with the unit, pay for my research paper then most times the issue is the hard circle and it ought to be supplanted.

Read Full Q/A … :
Unknown Printer

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :
Unknown Printer

HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:

Read Full Q/A … :
Unknown Printer

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :
Unknown Printer

49 error on LaserJet 1536dnf
ANSWER : How to rectify this problem

Read Full Q/A … :
Unknown Printer

Error Message
ANSWER : Are you sure that is SO2? HPs don’t give a code like that, maybe 50.2? which is a fuser error and replacing the fuser usually clears that if that is the code you’re getting.

Read Full Q/A … :
Unknown Printer

evenly spaced horizontal lines on hp laserjet III printout
ANSWER : The lines would be a toner cartridge problem. Which paper tray? The MF tray or the optional paper cassette?

Read Full Q/A … :
Unknown Printer