Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

yz Fuser error To continue turn off then on is displayed on the control panel, it indicates that there is an issue with the fuser. The XX and YZ are two digit codes that provide information on the specific issue causing the error. Press the power button to turn the printer off, and then back on to clear the error.
A high fuser temperature error has occurred. Note: A fuser error might occur because of inadequate power supply, inadequate line voltage, or a fuser problem.
00 Fuser error indicates you have an actual fuser failure and the fuser needs replacing. Fusers are a consumable part and they are the main component in a printer maintenance kit; it is expected over the life of the printer you will replace the maintenance kit several times.
If you are experiencing a “50.7” fuser error, first turn the printer off and back on. Sometimes the error will temporarily go away with a reboot so you can print a few more pages, but usually the error reappears.
Error 50 is Invalid destination number.
I found the following: Error 50 means that the heating of the fuser unit is no longer working. This is usually a burnt-out heating lamp,or a defective thermal fuse.
The P4014 series use a thin fuser sleeve as a medium to heat the paper. Error 50.8 suggests one end of the fuser is not heating up which may be damage to the sleeve or heavy media.
50.2 error indicates that the printer is not heating up fast enough. This can be caused by a bad heating element in the fuser but can also be caused when the printer does not have adequate power due to overloaded circuits or being plugged into a power strip or surge bar that limits current flow.
50 error is a fuser error and means the fuser needs to be replaced. Do a search for the part on google and then see if it is worth repairing based on cost of the fuser and if you will need to hire someone to replace it for you.
If you see the error message “50.2 Fuser Error” on your HP Color LaserJet CP2025 series printer, you probably need to replace the fuser. Fusers are a consumable part and it is expected over the life of the printer you will replace the fuser several times.
The 50.1 fuser error message refers to a low temperature reading on your fuser. If you see the error message “50.1 Fuser Error” on your HP Color LaserJet 2820 or 2840 series printer, you probably need to replace the fuser. Fusers are a consumable part and are sold as part of a maintenance kit.
Look inside the fuser opening to make sure there is no debris or jammed paper. Remove any debris or jammed paper, if found. Hold the handles on each side of the fuser and reinstall it in the printer.
The BCCode 50 usually occurs after the installation of faulty hardware or in the event of failure of installed hardware (usually related to defective RAM).
Error code 50 in the USB drive means users cannot move or copy files from external devices such as USB drives. Multiple reasons can lead to this error, such as corrupted NVRAM/PRAM, system files, etc.
unable to send sms error code 50 happens when the sms service has been blocked for 24hrs as per government rule. usually this happens after sim card replacement in any operator.
Er/30 or Er/50 to Er/55 displays and the Attention light is on. The printer is in an error state. Reset the printer to resolve the issue. With the printer turned on, disconnect the power cord from the printer.
Error code 50 usually refers to the fuser or part of the print assembly: https://www.printertechs.com/printer-troubleshooting/hp-error-codes/195-numeric-error-codes-50-59-hp… Try to look up the event log on the printers control panel or EWS. See if there is a more detailed description for us to research with you.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :
Unknown Printer

hp laserjet 4250n service error 49.4c02
ANSWER : The response by DMZCompute worked perfectly. Thank You!

Read Full Q/A … :
Unknown Printer

error code 98.00.00
ANSWER : According to the service manual http://www.laserpros.com/pdf/HP_TOCs/HP-600-M601-M…

Read Full Q/A … :
Unknown Printer

Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.

Read Full Q/A … :
Unknown Printer

HP 9040 MFP Error code
ANSWER : bonsoir

Read Full Q/A … :
Unknown Printer

HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:

Read Full Q/A … :
Unknown Printer

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :
Unknown Printer

error 50
ANSWER : Most likely the quartz lamp in the fuser assy. burned out. you can remove it and check the resistance on the 2 large pins in the connector. Should be several ohms.

Read Full Q/A … :
Unknown Printer