HP LaserJet 9000

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

It means the top of the paper isn`t being detected arriving at the fuser delivery sensor.
If you are seeing a “50.1 Fuser Error” on your HP LaserJet 5000 or 5100 series printer, you probably need to replace the fuser. Fusers are a consumable part and are sold as part of a maintenance kit; it is expected over the life of the printer you will replace the fuser several times.
An Er/04, Er/05, or Er/06 error message indicates a paper jam. Find and clear the printer of any jammed paper, or reset the printer if the printer has no jammed paper.
90 or 59.00. A0 Error resulting from a registration assembly and/or paper feed assembly that is jammed/stuck.
A piece of paper stuck in the paper tray or inside the printer can create a paper jam. Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer.
The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.
The event code: 13. B9. FF indicates that the printer believes there is a jam at the fuser output sensor, at power on. That means that printer has been power cycled, and the printer detects paper under the fuser output sensor while checking during the boot process.
A 13. B2. FF paper jam error appears on the control panel when paper is jammed in the top of the printer. Check the printer for jammed paper and clear the jam, if needed.
Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.
59.10 is a main drive error, which could be a bound up fuser. 51.10 is a laser error, which could be a bad laser unit. Which error do you have? If the printer can print an engine test, then you may have a bad formatter.
This error is specifically related to the fuser drive motor itself. The manual states that it`s a “fuser motor start up error“.
This jam occurs when residual paper is detected at the Tray 2 feed sensor (SR11). Open Tray 2, remove any jammed paper, and then close the tray. Open and close the upper right door to allow the printer to attempt to clear the jam.
When HP`s latest update occurs, the printer will not print and will display the error message, “Indicated cartridges blocked for containing a non-HP chip. Event Code: 10.00. 46.” The update will occur automatically and without warning, and once updated, the change to HP OEM cannot be reversed.
yz Fuser error To continue turn off then on is displayed on the control panel, it indicates that there is an issue with the fuser. The XX and YZ are two digit codes that provide information on the specific issue causing the error. Press the power button to turn the printer off, and then back on to clear the error.
Among the more common technical issues that may bring down a printer are disconnected cables, malfunctioning routers, and low ink levels. Moreover, software problems such as interrupted connections or incorrect settings in your system`s drivers can also cause your printer to show up as offline.
yz Fuser error To continue turn off then on is displayed on the control panel, it indicates that there is an issue with the fuser. The XX and YZ are two digit codes that provide information on the specific issue causing the error. Press the power button to turn the printer off, and then back on to clear the error.
Turn the printer off, wait 10 minutes, and then turn the printer on. 2. If the message persists, reseat the fuser. If that does not work, replace the fuser.
you have a loose or faulty connector on the fuser drive motor or one of the sensors, which will probably require a visit from a service tech. error while printing or after it warmed up.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Laserjet 9000 57.5 cycle power
ANSWER : according to the manual, the solution should be replacing part RH7-5296-000CN (or use alternate part RH7-1658) for 9000 / 9040 / 9050….have you tried it? …..if you’ve got any questions, contact me, Audrey, case study writer in tech and stuff

Read Full Q/A … :

HP LaserJet 9000

HP ScanJet 9000 service manual required
ANSWER : Scanner write some numbers, How i can know that number’s mean?

Read Full Q/A … :

HP LaserJet 9000

LaserJet 2200d Stopped Working
ANSWER : I am able to print a demo page and no lights blinking, tried different slots to no avail

Read Full Q/A … :

HP LaserJet 9000

HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:

Read Full Q/A … :

HP LaserJet 9000

How to copy a card slot in HP laserjet 4250N
ANSWER : None that I know of, using a computer is likely your best option but I never attempted it.

Read Full Q/A … :

HP LaserJet 9000

evenly spaced horizontal lines on hp laserjet III printout
ANSWER : The lines would be a toner cartridge problem. Which paper tray? The MF tray or the optional paper cassette?

Read Full Q/A … :

HP LaserJet 9000

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :

HP LaserJet 9000

LaserJet 4 won't Power Up
ANSWER : I haven’t seen that particular behavior on that model. It either works or it doesn’t. My first choice would be the power supply.

Read Full Q/A … :

HP LaserJet 9000