Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

There are four primary causes for horizontal banding on prints from inkjet printers, (1) nozzle clogs, (2) mis-aligned print heads, (3) low quality print settings (4) incorrect paper thickness settings. Below we will describe each of these causes for horizontal banding as well as ways to try and fix them.
The streaks or lines might be caused due to low ink levels in one or both ink cartridges. Check the ink levels using the HP Toolbox to determine if the ink cartridges are low on ink and need to be replaced. note: Ink level warnings and indicators provide estimates for planning purposes only.
Check Cables and Printer USB Ports

Check all cable connections (including the power cord) on the printer side. If the printer does have power and you`ve properly connected the communication cable, but the printer is still not recognized, try switching to a different USB port on the PC.

Banding happens when you do not have enough information in your file. Or you push the edits to an extreme. Avoid banding by making a well-exposed photograph and saving it as an uncompressed RAW file. To fix color banding, make subtle edits and limit how much you compress the photo when exporting as a JPEG.
If your laser printer is causing horizontal black lines you either have a problem with the optics or the drum. Cleaning the optics and replacing the drum should fix the problem in most cases.
Banding is caused by the harder rollers being less water-receptive than softer ones, non-alcohol solutions having a harder time adhering to their surfaces. The solution is to use softer rollers, such those possessing a durometer of 18:22.
HP has determined that 99% of all lines and streaks on copies made by feeding the original documents through the ADF are caused by debris on the ADF glass. Debris can include dust, paper or toner dust, residue from sticky note adhesive, correction fluid or tape, ink, fingerprints, and more.
Lines or streaks always appear in printouts when the cartridges begin to run out of ink. Replace print cartridges that are out of ink or low on ink.
Ghost prints happen when the drum or fuser unit within your printer become faulty. Because a fault with this element won`t heat the particles of the toner to a high enough temperature, the marks being made on the paper are much lighter in colour and appear more faded than typical documents.
Banding is the process of one or more product being wrapped with a thin band of paper or film. An efficient way to bundle, label or seal your products.
The effect of banding appears when the transition between tones are not smooth and is enhanced with almost every additional adjustment. In areas with a lot of detail, we will not be able to recognize banding. Banding only emerges in seamless areas with similar shades of the same color.
The paper type that you choose tells the printer how much ink to lay down onto the paper. When this is too little on an absorbent paper (like sublimation paper) it can cause lighter banding.
If your printouts are blurry or smeared, try these solutions: Make sure your paper is not damp, curled, old, or loaded incorrectly in your product. Use a support sheet with special paper, or load special paper one sheet at a time. Make sure your paper meets the specifications for your product.
Banding is a defect in inkjet printing that will appear as horizontal or vertical lines, streaks or bands in the printed output. Everyone will eventually experience some type of banding with their inkjet printer. To resolve the issue, it is important to quickly identify the type of banding that is occurring.
The paper type that you choose tells the printer how much ink to lay down onto the paper. When this is too little on an absorbent paper (like sublimation paper) it can cause lighter banding.
If your printouts are blurry or smeared, try these solutions: Make sure your paper is not damp, curled, old, or loaded incorrectly in your product. Use a support sheet with special paper, or load special paper one sheet at a time. Make sure your paper meets the specifications for your product.
If your printouts are blurry or smeared, try these solutions: Make sure your paper is not damp, curled, old, or loaded incorrectly in your product. Use a support sheet with special paper, or load special paper one sheet at a time. Make sure your paper meets the specifications for your product.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP Laserjet 2200, Tray 2 Pickup Problem, Gears Clicking
ANSWER : Definitely not a solenoid problem. I’ve worked on tens of thousands of printers and never replaced a single solenoid. You probably knocked something loose when you installed the pickup roller. Maybe something to do with the gear on the end of the pickup roller shaft. You’ll need to take the gear assembly off to be able to see it.

Read Full Q/A … :
Unknown Printer

HP CLJ 8550 does not recognize new Magenta toner
ANSWER : There’s a menu option to tell the printer it has a fresh toner cartridge.

Read Full Q/A … :
Unknown Printer

HP Color Laserjet 3800 problem when printing color
ANSWER : Do a cold reset

Read Full Q/A … :
Unknown Printer

How to copy a card slot in HP laserjet 4250N
ANSWER : None that I know of, using a computer is likely your best option but I never attempted it.

Read Full Q/A … :
Unknown Printer

HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:

Read Full Q/A … :
Unknown Printer

HP Laserjet M3035xs RFU Upgrade
ANSWER : There’s no way.

Read Full Q/A … :
Unknown Printer

HP LaserJet 1160 pick-up problem
ANSWER : Take the black rubber roller out. Clean it and turn it 90-180 degrees so there is fresh rubber in the “corner”.

Read Full Q/A … :
Unknown Printer

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :
Unknown Printer