Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Look for jammed paper or debris inside the printer, and then use both hands to remove any that you find. Use both hands to remove any jammed paper or objects from the input bin. Align the cartridge with the tracks inside the printer, push in until firmly seated, and then close the toner access door.
An Er/04, Er/05, or Er/06 error message indicates a paper jam. Find and clear the printer of any jammed paper, or reset the printer if the printer has no jammed paper.
The HP Printer Error Code 11 means Paper Out. When your HP printer isn`t out of paper, this probably means there`s a problem with the paper tray or paper sensor.
00 Fuser error indicates you have an actual fuser failure and the fuser needs replacing. Fusers are a consumable part and they are the main component in a printer maintenance kit; it is expected over the life of the printer you will replace the maintenance kit several times.
The four standard cartridges would be present attached to a rotating device called Carousel under the printer cover. The issues with the carousel rotation and the misplacement of the cartridges upon the printer devices would result in issues with the printer device called as printer error 54.2.
a 52 Scanner error indicates the laser/scanner which writes the image to the drum has malfunctioned. This is a hardware error and most times the actual laser/scanner assembly needs to be replaced. If under warranty contact hp for service.
Any of these error codes (51.2c , 51.2m , 51.2y , 51.2k) points to a failure with one of the laser scanner assemblies on the HP Color LaserJet 4600 series. To solve this error code, replace the corresponding laser scanner.
Error indicates it is Lower exhaust fan failure. 1. Check the fan on the lower left side of the product.
During a print job, the printer stops feeding pages, an E4 error displays and the Resume light blinks. This indicates that paper might be jammed inside the printer.
That error code indicates a failure of the yellow laser scanner. Unplug and leave for a few minutes, also make sure you are plugged directly into the wall and not into a surge protector.
The 41.2 error in the LaserJet 5Si, 8000, 8100 and 8150 is typically caused by high voltage arcing that disrupts the beam detect circuit. The most common cause of arcing is a bad connection to the transfer roller.
Possible causes for this error include: Swing arms are not engaged. Lift motor or clutch failure. Dirty or defective encoder disk/sensor.
Error 50.2 suggests the fuser can`t heat up properly. This might be fuser failure but could also be a power supply issue. Plug the printer directly into a wall socket, not into an extension. Try turning off, wait 20 minutes then on again.
Possible causes for this error include: Swing arms are not engaged. Lift motor or clutch failure. Dirty or defective encoder disk/sensor.
For anyone else who finds this page when tracking down this error, Error 79.8109 is simply the result of using the wrong printer driver (i.e. the HP Universal PCL6 driver, as provided under Windows 8 and 10). This driver does not work correctly with this printer. In general this error isn`t a formatter problem.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

49 error on LaserJet 1536dnf
ANSWER : How to rectify this problem

Read Full Q/A … :
Unknown Printer

HP LaserJet 49 Error Troubleshooting
ANSWER : One must give a chance to 25dollarsupport its a Fix $ price Computer Tech support company, which is the best option in present crowded market. Quite dependable and cost effective..

Read Full Q/A … :
Unknown Printer

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :
Unknown Printer

HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:

Read Full Q/A … :
Unknown Printer

HP Laserjet M3035xs error 13.17.00
ANSWER : If the misstep thinks of no interface join connected with the unit, pay for my research paper then most times the issue is the hard circle and it ought to be supplanted.

Read Full Q/A … :
Unknown Printer

HP Officejet Pro 8500 Carriage Replacement steps
ANSWER : Hi Mark:

Read Full Q/A … :
Unknown Printer

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :
Unknown Printer

HP Officejet Pro 8500 Wireless with fake paper jam
ANSWER : HP Officejet is by far one of the frustrating piece of equipment I have ever owned. I bought it as unused in the package, at that point no warranty left. less than 6 months and 500 pages the white cog gear wheel broke. Luckily with instructions in this site I manage to glue it back together. Then I bought new ink – problems started as they were not original HP 30$ per cartridge. Ordered originals (here in China), took over one week to get them. Then found out that printhead needed to be replaced => more than 100$ spent. Still constant problems: If my wife kids print, I need to be stand-by as you never know what happens. Really an Office level equipment. After cleaning one paper jam I broke the encoder tape, took me another 4 hours to get it fixed. Then broke the cog gear again and got it displaced. Another 4 hours. Only reason I am not throwing this s***t out of window is that there are still ink left. Luckily this drinks them like a horse, for sure I will no more buy new ink. I will get a new laser instead, and not from HP. About cog wheel fixing: make sure that the white wheel is positioned correctly so that the small torx in shaft goes into the slit in the white wheel. When fitting the black cover back, make sure that the white washers on both sides fit into to slits of the black cover. Good luck.

Read Full Q/A … :
Unknown Printer