Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Clean the rollers inside the printer, and then try to print again.
The paper might not be engaged with the feed rollers. The paper-width guide is pressed against the paper stack too tightly. The paper tray is not completely inserted into the product. The paper settings in the print driver do not match the paper loaded in the paper tray.
Pull the jammed paper down and out of the printer. Open the back cover (back output tray). Pull the tab toward you to open the fuser cover (1). Pull the jammed paper out of the fuser unit.
A piece of paper stuck in the paper tray or inside the printer can create a paper jam. Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer.
Any time your printer halts because of a paper jam, check the tray that holds the paper. Most likely you`ll find that at least one of the guides that keeps the paper in place is a little off.
Turn the printer off then back on. If the issue persists, turn the printer off, unplug the power cord and then wait at least three minutes before plugging the power cord back in and turning the printer back on. If the issue persists, ensure the product is running the latest firmware available from HP.com.
Using both hands, put one piece of paper in the manual feed slot until the front edge of the paper touches the paper feed roller. Once the machine has grasped the paper, let go. The side to be printed should be faced up. The machine will hold the paper in place until the print data is sent to the machine.
Open the printer`s web page and Sign in as Administrator. On the General tab select Reset Factory Settings in the menu.
During a print job, the printer stops feeding pages, and a Paper Jam error message displays on the printer control panel. This indicates that paper might be jammed inside the printer. note: Paper jams can be real or false. The printer might report a paper jam even when there is no jammed paper.
One sensor is located in the printer carriage. A second sensor—the Auto Sense sensor—is located in the back of the printer near the paper `clean out` area. Each sensor performs a specific set of media detection functions.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

HP LaserJet 1200 Early Feeding Causes Paper Jam
ANSWER : Seriously, dmzcompute, you are awesome! And this is just what the internet does so well: a specific fix for an esoteric problem, thus keeping a 15 year old machine alive another day. Thank you!

Read Full Q/A … :
Unknown Printer

HP Laserjet 6MP wont feed paper
ANSWER : I had a similar paper pickup problem on laserjet 6mp. The printer would go through start-up sequence fine but when it received a print job you could here the main gears/rollers turning but no clicking from paper pickup solenoid, then eventually error lights would come one . I incorrectly assumed it was an error with the paper pickup mechanism and wasted a whole day taking the printer apart and replacing the paper pick mechanism. Long story short, if I had bothered to figure out the secondary error light codes from the start, I would have realized it was just a bad fuser and would not have wasted so much time.

Read Full Q/A … :
Unknown Printer

Paper jam in tray 2 (but no paper pulled from tray) also M476DN models
ANSWER : Isopropyl alcohol is not recommended for rubber rollers. It dries out the rubber and hasten it’s cracking and breaking. It will do nothing to restore the grip. Those rollers are really hard to replace. It would be easy if that dumbass secondary menu really worked. None of the techs I’ve spoke to ever got into it. Everyone I know sends a print job and listens for the roller to rotate into position where you can pull it off.

Read Full Q/A … :
Unknown Printer

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :
Unknown Printer

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :
Unknown Printer

Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳

Read Full Q/A … :
Unknown Printer

Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.

Read Full Q/A … :
Unknown Printer