Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

A piece of paper stuck in the paper tray or inside the printer can create a paper jam. Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer.
A 13. FF. FF error is related to jams in the paper path. These errors indicate that the product powered up with a jam.
Dust, dirt, or debris: Not cleaning the HP Printer can also result in a paper jam error. So, if you find that no paper is stuck but a paper jam error showing, you must check for the dirt or dust on the device.
The 13. A4. D4 indicates that there is a “paper delay” jam in Tray 4. Which means that paper did not reach SR8 (sensor 8) in the allotted time necessary after the start of paper pickup from Tray 4.
A paper jam is when paper or other printed material gets stuck or lodged in a printer and cannot eject.
This error can mean that an electrical component is disconnected or is having difficulty communicating with the other components. If you`re getting this error, power cycle your printer by turning it off for one minute and then restarting it.
Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.
Step one: Perform a power reset

With the product turned on, disconnect the power cord from the rear of the product. Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet.

202.17 Fuser Paper Jam on a Lexmark C746, C748, X746, and X748 Color Laser Printer. Overview. A `202.17` Fuser Paper Jam error message means that the fuser exit sensor is broken or stuck, or else it is merely covered up by paper from a previous paper jam.
Common causes of paper jams include: Damaged rollers. Inserting paper that is incompatible with the printer. Loading the paper incorrectly.
Misfeeds occur frequently. The paper is damp. Use paper that has been stored in the recommended temperature and humidity conditions. For details about the proper way to store paper, see Paper Precautions.
If the [ ] indicator is blinking, a paper jam occurs inside the printer. Follow the procedures in this section to remove the jammed paper. Use caution to avoid cutting your hands.
Cause: Paper is jammed inside the printer. Remedy: Remove the jammed paper and set the paper cassette and covers to the original position.
Type Mismatch (Error 13) occurs when you try to specify a value to a variable that doesn`t match with its data type. In VBA, when you declare a variable you need to define its data type, and when you specify a value that is different from that data type you get the type mismatch error 13.
This error code indicates that the current user did not have permission to access an operating system file. This error usually occurs if the user does not have read or write permission on a file (e.g. PERSON. RRN) or a directory (e.g. the directory containing .
The 13.02 error message indicates that paper did not clear the top of page sensor (PS103) within the specified amount of time allotted by the DC Controller. This sensor is located underneath the registration assembly. The jam message may vary depending on the location of the page or pages that may be jammed.
This jam occurs when residual paper is detected at the Tray 2 feed sensor (SR11). Open Tray 2, remove any jammed paper, and then close the tray. Open and close the upper right door to allow the printer to attempt to clear the jam.
The printer experiences a paper jam from Tray 2, or the printer does not pick paper or picks more than one sheet from Tray 2. A 13. B2. D2 paper jam error usually occurs when paper does not leave the paper tray.
Some random crash 49.38. 13 may happen when the BarDIMM Pro is installed in the printer equipped with that firmware and other solutions. The defect is fixed in HP Futuresmart 5.2 firmware. If your HP printer does not have Futuresmart 5.2 available, we recommend you downgrade to Futuresmart 4.11.
Wipe the sensor window with one of the cotton swabs provided in the Printer Cleaning Kit, slightly dampened (not soaked) with isopropyl alcohol, to remove dried ink. If the sensor window is heavily coated with dry ink, you may need to apply some pressure while wiping, helping the cotton to absorb the ink.
With the printer turned on, disconnect the power cord from the rear of the printer and also unplug the power cord from the wall outlet. Remove USB cable, if present. Wait for 2-3 minutes, press and hold the power button on your printer for about 30 seconds to remove any additional charge.
Wait for the fuser to cool before handling it. If jammed paper is visible, remove any jammed paper from the rear door area. Close the rear door and the front door. If the error persists, contact your HP-authorized service or support provider, or contact customer support at www.hp.com/go/contactHP.
The message “Fuser Kit Low” or “Fuser Kit Very Low” on your HP Color LaserJet M553 series printer is a warning that you have reached the recommended number of prints for your fuser assembly. (The fuser assembly is the consumable part in your printer which heats up and bonds toner to the paper.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

HP LaserJet 1200 Early Feeding Causes Paper Jam
ANSWER : Seriously, dmzcompute, you are awesome! And this is just what the internet does so well: a specific fix for an esoteric problem, thus keeping a 15 year old machine alive another day. Thank you!

Read Full Q/A … :
Unknown Printer

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :
Unknown Printer

Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.

Read Full Q/A … :
Unknown Printer

Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳

Read Full Q/A … :
Unknown Printer

Paper Jam 13
ANSWER : Sticky paper pickup solenoid. Since MF tray doesn’t use it, it works fine. Solenoid is located on right side of printer at the end of the paper pickup roller shaft. You need to remove the solenoid, take the plate and spring off the top and then scrape off the gooey residue that’s causing it to stick. Then you get a thin piece of sticky backed felt and put it on top of the metal base. You can find some at the local hardware store, they’re used on the bottom of chair legs.

Read Full Q/A … :
Unknown Printer

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :
Unknown Printer

Paper jam in tray 2 (but no paper pulled from tray) also M476DN models
ANSWER : Isopropyl alcohol is not recommended for rubber rollers. It dries out the rubber and hasten it’s cracking and breaking. It will do nothing to restore the grip. Those rollers are really hard to replace. It would be easy if that dumbass secondary menu really worked. None of the techs I’ve spoke to ever got into it. Everyone I know sends a print job and listens for the roller to rotate into position where you can pull it off.

Read Full Q/A … :
Unknown Printer