Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

power requirements 220V to 240V (+/-12%) 50/60 Hz (+/-3), 2.7 Amps maximum. power consumption 0 watts (off), 7 watts maximum (Powersave/standby), 285 watts maximum (printing). dimensions (w x d x h) Out of package: 415 x 486 x 254 mm. Packaged: 500 x 400 x 450 mm.
If you see this error code 50.5 on an HP LaserJet 4200, 4240, 4250, 4300, or 4350 series printer, the fuser installed in the printer is registering as an incorrect fuser for that model printer.
A 49 error typically occurs when the printer attempts to perform an action that the firmware is not capable of performing or might not be designed to handle, for example: Printing files that include unsupported printer commands. Interfacing with a third-party solution that was not designed to work with the printer.
It has an input range of 100-240 volts and two output voltages – 32 volts and 12 volts.
Typically, 24 Volt are used when “regular” power is available. Solar power asks for 12 Volt. Thermal printers draw high currents for very short time periods (usually under one millisecond).
41.02 error on this printer is a laser/scanner error. If the message does not clear, then you need to replace the laser/scanner. If you are not getting a 41.02 error, then report back with the correct number. The 05 does not mean anything.
41.2 Error Code on HP Laser Printers

The arcing occurs in the toner/transfer area, and can be caused by a defective toner cartridge, bad high voltage or ground connections to the toner cartridge or transfer roller, or a defective high voltage power supply.

This error is primarily caused by a transfer alienation failure in which the ITB is stuck and unable to rotate, the SR9 sensor (the primary transfer roller disengagement sensor) has gone bad or the fuser drive assembly has failed.
Make sure that the tray is loaded with the correct paper size and that the sliding paper guides are correctly adjusted to the correct paper size. Print internal pages from all trays to verify that this error only occurs when printing from the PC.
00 Fuser error indicates you have an actual fuser failure and the fuser needs replacing. Fusers are a consumable part and they are the main component in a printer maintenance kit; it is expected over the life of the printer you will replace the maintenance kit several times.
An E0 error indicates an unusable cartridge. This condition occurs when at least one ink cartridge needs attention, is faulty, incorrect, missing, damaged, or incompatible. Reseat both ink cartridges, clean the ink cartridge contacts, restart the printer, and replace one or both ink cartridges if necessary.
Horsepower. The relationship between an electric motor`s horsepower and torque is that, for a given electric motor design, increasing the voltage or RPMs will increase HP (horsepower).
1-1 of 1 Answer

Yes, it works with an input voltage of 100 to 240 VAC (+/-10%).

Yes, it works with an input voltage of 100 to 240 VAC (+/-10%).
Yes, Inkjet printers are dual-voltage and supports 100v to 240v. You may only need a compatible cable or adapter for the local power socket type.
The power consumption of an average inkjet printer is 30 to 50 watts in printing mode and around 3 to 5 watts while on standby mode.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:

Read Full Q/A … :
Unknown Printer

Laserjet 4250 print quality issue (see image)
ANSWER : It looks like a fuser problem. One way to prove it is with the half-stop test. Put a sheet in the drop down manual feed tray. Send a print job and watch the paper. When the end of it is about to enter the printer, open the lid and take out the toner cartridge. Look at the printed image. If it looks OK, then it is a fuser problem. If not, then it is a toner cartridge issue since it hasn’t gone through the fuser.

Read Full Q/A … :
Unknown Printer

Service manual for an HP Laserjet 4250 (or 4250n)
ANSWER : Hello all,Can someone please tell me where to find service manual for a 4250 or 4250n printer?I used Google, Fileshare.eshop.bg, peer-to-peer, but with no avail …Thanks alot for your answers!

Read Full Q/A … :
Unknown Printer

HP LaserJet 49 Error Troubleshooting
ANSWER : One must give a chance to 25dollarsupport its a Fix $ price Computer Tech support company, which is the best option in present crowded market. Quite dependable and cost effective..

Read Full Q/A … :
Unknown Printer

HP 4250, error 54.1 Remove sealing tape from toner
ANSWER : I am having the same problem as everyone else can someone send me a new link or the pdf

Read Full Q/A … :
Unknown Printer

laserjet 4200 4250 4300 4350
ANSWER : I just (by mistake) bought the tone 381 for 4200 by mistake on eBay. I just cut off the extra plastic noses and it does work now with my 4250! I’m really glad about that ;D

Read Full Q/A … :
Unknown Printer

HP 4250 13.06.00 Fuser output paper stop !
ANSWER : pick up solenoid

Read Full Q/A … :
Unknown Printer

HP Laser Jet 4250 13.01.00 Jam in Tray 2
ANSWER : did you check if there’s multiple feeding while pulling papers

Read Full Q/A … :
Unknown Printer