laserjet 3p

The printer is either low in toner, the density is set too low, or the Economode may be turned on. Remove the toner cartridge and shake it. This will redistribute the toner and often will temporarily solve the problem. However, this usually indicates it is time to install a new cartridge.

An Er/03 error message indicates the printer failed to pick a sheet of paper to print. Remove the stack of paper from the tray and check the condition of the paper. Reload the paper, and then try to print, copy or scan.

Your printer should have been packaged with a USB cable regardless of whether it is a wireless or wired printer. Plug the cable into your printer and your computer`s USB port. The direct linking should trigger your computer to recognize the printer and start up the software needed to complete the installation.

Turn off the HP printer and unplug it from the power source. Also, shut down your computer and unplug any external devices. Wait for a few minutes and then plug in the printer and turn it back on. Finally, turn on your computer and check if the error state has been resolved.

Make sure your Wi-Fi network and printer setup meet connection requirements. Restart the printer and the computer or mobile device to clear possible error conditions. Make sure the printer is not connected to a computer with a USB cable.

Most printers will stop working when they`re out of paper, ink or toner, or if the unit detects an issue with the ink or toner cartridge. When this occurs, you might receive an error message or notice blinking green or amber lights on your printer.

If your printer is turned on, disconnect the power cord from the printer. Keep the power plug unplugged for 60 seconds, reconnect the power cord to the wall, and turn on the printer. If the error persists, remove the cartridge from the printer, clean the cartridge contacts with a cloth, and reinstall the cartridges.

In Windows, search for and open Add a printer or scanner . Click Add a printer or scanner, and then wait for Windows to locate available printers. If your printer is found, click it, and then click Add device to complete the driver installation.

Select the Start button, then select Settings > Devices > Printers & scanners. Under Add printers & scanners, select Add a printer or scanner. Choose the printer you want, and then select Add Device.

The default administrator or root password for all HP-provided Build Plans is: ChangeMe123! CAUTION: HP strongly recommends changing this password before deploying to any servers. See Set (encrypt) the administrator/root password for details.

Right-click the printer you want to manually enable and click Printer Properties. Under Advanced and Driver, note the name of your printer driver. Connect to your host computer and go to the manufacturer`s website of the printer driver. On the host computer, download the printer drivers associated with your printer.

1: Check Printer Power, Cables, and Paper

Check that the correct paper is properly loaded into the printer and is not jammed. Replacing damaged cables, plugging in loose or disconnected cables, and fixing paper jams as necessary may resolve the issue.

Remove and Re-Add Your Printer in Windows

If this happens, go to Settings > Devices > Printers & Scanners, select your printer, and remove it. Then click Add a Printer or Scanner to re-add it to the device list.

Make sure your router is on and connected to the internet. If you have another device on the same router, make sure it can connect to the internet. If the router is not connected to the internet, contact your network service provider. Check the printer connection to the router.

1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.

This error code can appear for a few reason such as cable issues, firmware errors or hardware faults. You can try the reset processes as stated at the top of the page, then if the error code still displays update the firmware, also try using different printer cables.

Error Code 3 is a Windows error code that appears when the computer cannot find the specified path.

Operating system error = 3(The system cannot find the path specified.). Verify the path that`s set for the ErrorLog file by using SQL Server Configuration Manager. You can also verify the path in the following registry entry: Subkey. Data.

Restart your printer, router, and mobile device

Turn off the printer, and then turn it on again. Disconnect the power cable from the router, wait ten seconds, reconnect the cable, and then wait for the internet connection to complete. Turn off your phone or tablet, and then turn it on again.

LaserJet printers: Press and hold the Wireless button for 10 seconds or until the Ready light blinks, or go to the Wireless menu and select Wireless Network Test. Laser NS and Neverstop Laser printers: Press and hold the Resume and Wireless buttons for 3 seconds.

Some HP printers come with a feature called Wi-Fi Protected Setup (WPS) which allows you to connect the printer to a wireless network without the need for a computer or the network name and password. Note: If Enter the WPS PIN for your printer displays during a printer setup, click Cancel in the message window.

If your printer is compatible with Windows 10, download and run the Print and Scan Doctor to detect and fix isses. If problems persist, reinstall the latest HP printing software. Download and Install the latest HP printer software and driver.

Reset. Resetting the printer stops printing and clears the current print job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully.