HP DesignJet 30
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
The printer is either low in toner, the density is set too low, or the Economode may be turned on. Remove the toner cartridge and shake it. This will redistribute the toner and often will temporarily solve the problem. However, this usually indicates it is time to install a new cartridge.
Make sure that your page settings are set to print all pages and to print every page. Settings that cause some pages not to print are `manual duplexing`, `print every other page`, `print odd pages`, `print on both sides`, or similar settings.
Reasons why your HP printer has ink but won`t print
This may seem obvious, but it sometimes happens: first make sure your paper tray has paper in it. Misalignment, clogged printheads, faulty data communication or insufficient ink levels can also be sources of the problem.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
Select Start , then select Settings > Devices > Printers & scanners . Scroll down to Related Settings and select Print server properties. Select the Drivers tab, and see if your printer is listed. If it is, you`re all set.
Check the ink levels
Sometimes, the printer may not print black ink because it is low or empty. You can check the ink levels on the printer`s display, or by using the software that came with your printer. If the ink level is low, replace the cartridge or refill it according to the manufacturer`s instructions.
Several factors may cause the product to print blank pages, such as print settings, low ink, or the product itself. Check the following: Make sure the product is placed on a flat, stable surface that extends beyond the base in all directions. The product won`t operate properly if it`s tilted or at an angle.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
HP 2200 – Won't feed paper and squeals
ANSWER : My suggestion: laser mirror motor has dry bearing (the squeal) and the printer won’t feed paper until it gets up to speed. Someplace on fixyourownprinter is an article explaining how to get to the motor & put a drop of TriFlow Synthetic PTFE oil on it. Worked for me…
Read Full Q/A … :
HP DesignJet 30
HP Laserjet 1320tn printing grey instead of black
ANSWER : Try this test. Put a page into the manual feeder and do that same test. When the end of the page is just about to enter the printer, open the lid. Take out the toner cartridge and pull back the shutter. Look at the image and see if it is black. The explanation is that there is high voltage going to both the toner cartridge and the charge transfer roller below it. If the image on the drum is black, then the fault is at the transfer roller not getting enough high voltage. The transfer roller pulls the image off of the drum and down onto the paper. It would not be a laser scanner problem as any issue with it would not result in an overall gray image, but combination of gray and black. It will probably turn out to be a bad HV power supply, which will need replacement. I’ve never seen this particular problem on this model.
Read Full Q/A … :
HP DesignJet 30
HP LaserJet 2200D won't print configuration page
ANSWER : Find someone with a HP LaserJet 4100 and you can configure the card to the IP you want:
Read Full Q/A … :
HP DesignJet 30
Laserjet 4250 print quality issue (see image)
ANSWER : It looks like a fuser problem. One way to prove it is with the half-stop test. Put a sheet in the drop down manual feed tray. Send a print job and watch the paper. When the end of it is about to enter the printer, open the lid and take out the toner cartridge. Look at the printed image. If it looks OK, then it is a fuser problem. If not, then it is a toner cartridge issue since it hasn’t gone through the fuser.
Read Full Q/A … :
HP DesignJet 30
My 2550n Color LaserJet does not want to print in color
ANSWER : That model had issues with the carousel solenoid sticking. That might explain why it works after you let it sit for 10 minutes. The solenoid gets hotter with use which causes the deteriorated foam on it to become sticky and hold down the release plate instead of letting it go. This allows the carousel to spin when it is supposed to stop for each color. The solenoid is located on the right side of the printer. If you open the lid, it is just behind the opening at the top right. You need to remove the top of the printer and scrape off the goo on top of the solenoid body. I put a piece of thin sticky backed felt to replace it. Other people use electrical tape.
Read Full Q/A … :
HP DesignJet 30
Print file sent but no printing occurs
ANSWER : Been working on these since they first were released. Never seen a problem like yours. If it happens again, try doing an engine test, as it bypasses the formatter board. The engine test is located at the right side of the manual tray opening. Look for a hole in the side wall. Stick something like a paper clip into it to actuate the test button. It will then print a lined test page. If it does that, then it points to the formatter board as the cause of your problem.
Read Full Q/A … :
HP DesignJet 30
HP 2200 – blinking attention light and tray 2
ANSWER : Nice day. (QUALITY IS OUR CULTURE)
Read Full Q/A … :
HP DesignJet 30
HP Laserjet 2200, Tray 2 Pickup Problem, Gears Clicking
ANSWER : Definitely not a solenoid problem. I’ve worked on tens of thousands of printers and never replaced a single solenoid. You probably knocked something loose when you installed the pickup roller. Maybe something to do with the gear on the end of the pickup roller shaft. You’ll need to take the gear assembly off to be able to see it.
Read Full Q/A … :
HP DesignJet 30