Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Er/11, or Er/14, or Er/17 displays

The toner cartridge is not compatible with the printer. The toner cartridge has been protected on another printer.

Er/11, Er/14, or Er/17: The toner cartridge is not compatible with the printer, has been protected on another printer, or is an unauthorized toner cartridge.
This condition occurs when the toner cartridge is absent or not installed correctly. To resolve the issue, reinstall the toner cartridge.
Requirements: Operating System – Windows 7, Windows 8, Windows 8.1, Windows 10. Browser – Google Chrome 10+, Internet Explorer (IE)10.0+, and Firefox 3.6.x, 12.0+
Error code 11:00 on the indicates that the printer struggled to detect the dye film panels.
If you think you are seeing this message in error, visit the Disney+ Help Center (Error Code 11). It means that the film or show you`re trying to watch on Disney+ isn`t available in your country or region.
Error 11:11 is normally displayed on the front panel of your HP Designjet Printer because a fault has been detected with the trailing cable. The trailing cable is the component that provides communication between the printer electronics and the carriage PCA.
Re: B210 Error 11-1114

What you are seeing may be a PostScript error. Try using the PCL driver and see if you get the same issue or if you are using a PCL driver then try the PS driver. Confirm you have the most recent firmware loaded on your printer.

A `Paper has Jammed` message and light blinks

Remove any ejected paper from the front or back of the printer. Open the paper tray cover. Remove any loose photo paper from the paper tray, and then check for and remove any bent, wrinkled, or torn paper.

Press the WPS button on your wireless router. On the printer control panel, press the Wireless button . The wireless light starts to blink. Wait up to two minutes while the printer establishes a network connection with the wireless router.
Connect a USB cable to the USB port on the rear of the printer , and then to the computer. Make sure the printer firmware is up-to-date. Go to Software and Driver Downloads, type your printer name, and then press Enter. Install any available firmware updates.
Error 0x0000011B is a common issue on Windows systems and can have various causes. Here are the most common causes and how to resolve them: Driver conflict: This happens when two drivers access the same resources at the same time. To resolve this issue, check for any conflicting drivers and update or disable them.
To fix the error code 0x0000011b related to networked or shared printers, Microsoft says you should disable the print spooler privacy settings on both the Client PC (from which you work) and Print Server (Workstation to which the printer is attached).
What does that mean? A transaction with an identical amount and credit card information was submitted, which means that you tried to charge the same transaction twice. We suggest that you contact the card issuing bank for more information.
dll error code 11 is an indication of a faulty game or program. The issue may be caused by bugs within the application or compatibility problems with the system. To resolve this issue, you will need to uninstall the game or program first and then reinstall it from scratch.
00 or a 50.22. 11 error displays on the control panel, it indicates an issue with the fuser warming up. Step 1: Turn the printer off, and then on. Turn the printer off, and then on to clear the error.
Signal 11, also known as SIGSEGV (signal segmentation violation) is an error signal in Unix systems (Linux). The error appears when a program or code tries to access an invalid memory location. The operating system sends the signal 11 error to the program as a response.
The error messages might display for one of the following reasons: Er/11 or Er/13: One or more toner cartridges are not compatible with the printer. Er/14 or Er/16: One or more toner cartridges have been protected on another printer.
An 86:11 error on the printer`s front panel indicates a scan-axis shutdown during initialization. Typically, this error occurs when the printer detects an incorrect scan axis length.
HELP 16.83:11 – POST CURING BURST RESISTOR NOT CONNECTED

It`s a hardware error, there`s either an issue with the air curtain resistor or with the cable. If it happens consistently, you should contact your support representative.

The 41.2 error in the LaserJet 5Si, 8000, 8100 and 8150 is typically caused by high voltage arcing that disrupts the beam detect circuit. The most common cause of arcing is a bad connection to the transfer roller. Other possibilities are discussed at the end of the article.
Most printers will stop working when they`re out of paper, ink or toner, or if the unit detects an issue with the ink or toner cartridge. When this occurs, you might receive an error message or notice blinking green or amber lights on your printer.
The Power light blinks at a steady interval when the printer is processing a print job. If the Power light blinks fast, the ink cartridge door might be open, or the printer might be in an error state. If an error message displays on the computer screen, follow the on-screen messages to resolve the issue.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP Laserjet 4 Plus LED display dim
ANSWER : My HP Laserjet Plus’s LED display went blank around 6 weeks ago. It had been acting strangely for about a month, when ready, instead of the usual 00 READY it would display 000READY, which got my attention. Well, it suddenly went entirely AWOL. The service manual said to check:

Read Full Q/A … :
Unknown Printer

LaserJet 2200d Stopped Working
ANSWER : I am able to print a demo page and no lights blinking, tried different slots to no avail

Read Full Q/A … :
Unknown Printer

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :
Unknown Printer

HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:

Read Full Q/A … :
Unknown Printer

How to copy a card slot in HP laserjet 4250N
ANSWER : None that I know of, using a computer is likely your best option but I never attempted it.

Read Full Q/A … :
Unknown Printer

evenly spaced horizontal lines on hp laserjet III printout
ANSWER : The lines would be a toner cartridge problem. Which paper tray? The MF tray or the optional paper cassette?

Read Full Q/A … :
Unknown Printer

LaserJet 4 won't Power Up
ANSWER : I haven’t seen that particular behavior on that model. It either works or it doesn’t. My first choice would be the power supply.

Read Full Q/A … :
Unknown Printer

HP Laserjet M3035xs RFU Upgrade
ANSWER : There’s no way.

Read Full Q/A … :
Unknown Printer