Unknown Printer

Experienced technical support provide their insights in answering this question :
t60 fatal error

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Epson Printer Doesn`t recognise a new cartridge

This is to ensure it has clicked in place properly. If this doesn`t work, remove and inspect the cartridge chips. Clean away any dirt or ink that may be preventing it from being recognised. Refit and check if this has solved the problem.

Method 1 – Bypassng Ink Cartridge on Epson Printer

After opening the lid, hold the ink button down. When you find the ink holer is moving to its position, then open the cartridge`s lid which is having no ink. Close it again without removing the cartridge. Close the lid and start to print.

Verify the ink cartridge(s) is inserted properly. Some cartridges snap in place, and if they are not inserted fully, the printer won`t print anything. If a lever is moved from its original position to allow for installation of ink cartridges, ensure it is returned to its original position.
Hey, you can reset Epson ink cartridge without resetter! As shown above, you can reset Epson chips by pressing and holding the button above the chip with a bent paper clip for 10 seconds.
If any ink remains in the ink bottle after filling the ink tank, place the bottle cap tip securely on the bottle cap and store the ink bottle upright for later use. Replace the ink tank cap securely. Repeat the previous steps as necessary for each ink tank you need to refill. Close the ink tank unit cover.
Yes, you can reset the print settings to their original, default values. Press and hold down the Cancel button for 3 seconds. When the message to reset the printer to default settings appears, press OK to reset the print settings.
Remove all of the new cartridges you had installed and re-install the old (empty) cartridges that worked. Restart the printer, this should remove the not recognised error (and tell you some are empty).
Ensure that the supported settings are applied in the printer driver and click Print in Black to continue printing using Black Print Mode or Cancel Print to replace the expended cartridge.
First tip is resetting the printer`s memory so it can detect the data from your new cartridge. The second tip is manually cleaning your cartridges to free it from dust or debris so it can function properly. Take note that these tips for your printer not recognizing cartridges are applicable regardless of the brand.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Just installed new epson ink and have red light on
ANSWER : t60 fatal error

Read Full Q/A … :
Unknown Printer

Epson printer can't recognize Epson ink cartridge
ANSWER : Hi, my name is Jim.

Read Full Q/A … :
Unknown Printer

Epson 7880 ink pump sucking ink
ANSWER : Not ink pump, but air pump, to put the ink feed under pressure.

Read Full Q/A … :
Unknown Printer

Epson Stylus C90 (Red Light Continuously Blinks)
ANSWER : It looks like General Error occurs. Check for foreign objects inside the printer which may block the movement of printhead carriage, paper feed, etc.

Read Full Q/A … :
Unknown Printer

Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT

Read Full Q/A … :
Unknown Printer

Epson Stylus Photo R200 – flashing red lights
ANSWER : The R800 will flash the ink and paper lights alternately when the ink pads are assumed to be full from extensive head cleaning. Sometimes, if not always, the head will lock into place on the right side above the ink head cleaning sponges that release ink to the lower ink pads.To correct the problem you need to clean the sponge area, I use cotton swabs. If the head is locked to need to release the carriage lock with a screwdriver. This will require removing the cover, but not necessarily the bottom of the unit.There is a 179 page service manual available for download for $16.50. There are free downloads of this manual, but usually are missing the 100 pages.You can remove the cover by:1. Remove the three screws on the rear housing (One to the left of the power plug, one on the opposite side and one in the lower middle bottom.2. Remove the three screws inside the upper housing (Just under the lid where the hinge is).3. Remove the screw under the left and right side in back below the vents.4. In the back pull the white ribbon closest to you out of the block, do not try to remove the block itself.5. Place a screwdriver into the slot both on the right and lift of the bottom corners on the back to release the hooks that hold the upper unit.6. Lastly, put a screwdriver into the notches on the bottom of the printer located in the front right and left, they are spring loaded.7. Remove cover.8. The head lock release screw is in the right side of the printer and is partially covered by the lower housing. I drilled a half inch hole into the side as to be able to insert a screwdriver. Turn the screw to the left and the head will rise out of the locked position. You only need to turn enough to release the head.9. Clean the sponges and any areas you see with excess ink.10. Place the cover on the unit enough to plug the white ribbon back in and turn the unit on.If the printer lights stop flashing then you are all set.

Read Full Q/A … :
Unknown Printer

Epson Artisan 837 Cyan Ink Blotches-leaking
ANSWER : Just encountered same problem (with light magenta) and discovered it was my own fault! There’s an adhesive-backed piece of aluminum foil that serves as one wall of the ink channels in the white plastic transition junction where it connects to the printhead. In trying to clean the printhead, I apparently nicked that foil, but didn’t notice when I reassembled, so I created a real mess in the printer. I cleaned everything up and then carefully (to cover the damage but not plug the ink channel) smeared a light coating of Goop household cement over the nicked hole, let it cure for about 6 hours, put everything together, and the leaking stopped.

Read Full Q/A … :
Unknown Printer

Epson Stylus Photo R230(2 red indicator blinking)
ANSWER : 2 red indicator blinking

Read Full Q/A … :
Unknown Printer