Canon FC 330

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Press (Settings/Registration). Press [Adjustment/Maintenance] → [Maintenance] → [Clean Roller]. Press [Start]. It takes approximately 20 seconds to clean the roller.
If the paper feed roller is dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed roller. Cleaning will wear out the paper feed roller, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the front tray.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
Click Start, point to Settings, and the click Printers. Right-click the appropriate printer, and then click Properties. Click the Paper tab, and then click the paper size you want to use in the Paper Size box. Click OK, and then close the Printers folder.
Check that the paper guides are set in the correct positions, Hold the unlock lever and move the paper guides so that the projection is aligned with the index of the paper size to be loaded.
Press [Function Settings] → [Printer] → [Printer Settings].
If the paper feed rollers are dirty or have paper dust on them, the paper may not be fed properly. When this happens, you`ll need to clean the rollers twice: once with paper loaded, and once without.
If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary. Then reload the paper. If thick media does not feed, make sure you are loading it straight into the product, not at an angle. If paper jams when you print on both sides of the paper, try loading fewer sheets.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
To set up the user management after the setup is complete, you need to log in as an administrator. The default user name for the administrator is “Administrator” and the default password is “7654321”. When you are going to operate the machine as “Administrator,” change the current password to improve the security.
Press [ ] (Settings/Registration). Press [ ] or [ ] to highlight <Timer Settings>, and then press [OK]. Press [ ] or [ ] to highlight <Auto Reset Time>, and then press [OK]. Press [ ] or [ ] to specify the time for the Auto Reset Time to activate, and then press [OK].

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Optional 250 Sheet Feeder Tray (Q5931A – Tray 3) Constantly "Jams"
ANSWER : You don’t say if the paper moves at all. That’s key in determining the cause. If it’s not moving, then try swapping the rollers with tray 2. If it is moving out of the tray, then that would indicate there is some obstruction it is hitting on its way out of the tray. Hard to troubleshoot remotely when one doesn’t have specific details since we can’t see what is occurring.

Read Full Q/A … :

Canon FC 330

epson printer problems
ANSWER : My Printer Has A Internal Erro

Read Full Q/A … :

Canon FC 330

Printer stops pulling paper from tray 2 after a few sheets
ANSWER : Sticking pickup roller solenoid. Pretty easy fix. You need to remove the right side covers. The back one just slides off, but the top holds the front one. I usually just take the 2 right side screws off and gently lift the top enough to pop off the side panel. Open the metal door on the formatter assy. Then release the tab in the middle. There’s also a tab at the front of the panel. When putting it back on, make sure you engage the rocker switch and the metal rod before pushing it into place. When you get it open, you’ll see the solenoid at the bottom front. There’s 1 screw holding it in place. Remove it and take the top plate and spring off. Be careful not to lose the spring. Then scrape off the gooey crap on top and clean off the plate as well. I put a piece of thin sticky backed felt in place of the remnants of the disintegrating sponge that HP uses. You can find it at the hardware store used for the bottom of chair legs.

Read Full Q/A … :

Canon FC 330

HP PSC 2410 clicking noise problem
ANSWER : I have the same issue… I’ve tried everything above… I don’t believe it’s dust as this happens on and off occasionally… I think I may need to make a youtube video of me “fixing” this printer! I’m really frustrated with this thing!! If it doesn’t work soon, I’m gonna by the solution in the form of a hammer!

Read Full Q/A … :

Canon FC 330

Paper Feed Problem on HP R80
ANSWER : In the last examination it is our origination of death which chooses our responses to all the inquiries life puts to us. The most pleasant spot to be is in somebody’s idea; the most secure spot to be is in somebody’s petitions.

Read Full Q/A … :

Canon FC 330

problem in driver
ANSWER : we offer Assignment Help Australia for you do not waste more time to searching others just click us.

Read Full Q/A … :

Canon FC 330

Oki C5300 problem : network menu disappeared.
ANSWER : You need MuWin and your NIC firmware to upload to the host, but both things are keep under cover by OKI… Find attached old (and probably useless for you) files; check and say.. (https://mega.nz/#F!oEkA3JKZ)By the way, you should specify what firmware do you need ¿isn’t it? I don’t know yet what firmware uses my c511dn nor what NIC host it mounts… :~(

Read Full Q/A … :

Canon FC 330

problems with printing
ANSWER : Check your settings to make sure they are Left to Right print order. If they are then reinstall printer driver. If that doesn’t correct problem uninstall printer, reboot computer, and reinstall printer.

Read Full Q/A … :

Canon FC 330