Okidata Oki C 5150N
Is it necessary to change a drum when message “order K image drum” comes up?
Experienced technical support provide their insights in answering this question :
You don’t have to replace it until it wears enough to affect the print quality. You’ll get spots or stripes. Here you go on a free reset. If you read the thread, someone says the procedure also works on your model. http://www.fixyourownprinter.com/posts/33634
How to Identify and Fix Common printer Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
“DRUM LIFE” or “REPLACE DRUM” is a rough indicator that the image drum cartridge has reached the end of its life. If there are no problems with print quality even if this message appears, continue to use until there is no toner left. When out of toner, replace the image drum cartridge and toner cartridge together.
The image drum can print approximately 50,000 sheets of A4-sized paper (for simplex printing), but the actual printable number of sheets may vary with the usage condition. The above number is based on the general usage condition (three sheets at a time).
It has several different names, it`s also called the imaging unit, drum unit or photoreceptor drum. For a drum to transfer the text and toner to the page, it first receives a positive charge from the corona wire. A laser writes over the drum and leaves a negative charge where the text and/or images will appear.
Drum Error typically appears when the corona wire on the drum unit needs to be cleaned or when the drum unit needs to be replaced. If you replaced the drum and the message appeared or continued to appear immediately after installing the replacement drum, click here. 1. Clean the corona wire inside the drum unit.
There are many factors that determine the actual drum life, such as the temperature, humidity, type of paper, type of toner used, number of pages per print job and so on. Under ideal conditions, the average drum life is estimated at approximately 12,000 pages.
Toner is the powder ink that latches on to the paper to create text and images. It is stored in the toner cartridge. An image drum is the unit that copies the text and images from the computer and then transfers them to the paper, along with the toner.
The drum plotter is a specialized output device whose name indicates its function. This device works by moving a pen on a single axis track while the paper moves on a cylindrical drum. Typically, the drum moves the paper to the right and left, while the pen or pens draw up and down.
You`ll know the drum is dirty if you notice that the print quality has become blurry and features blank spots or oddly-colored spots despite having full toner cartridges. Horizontal lines across the printout when the paper passes over a dirty area are another sign that it`s time for some maintenance.
The drum unit may need replacing if you notice the printer producing blurry, low-quality images. Black or colored toner spots on printouts also indicates a failing drum unit. In some cases, horizontal lines may develop across the printout every time the paper passes the failing part of the drum.
You can set when to display the “Image Drum Near Life” message. Press [Device Settings] > [Admin Setup] > [User Install] > [Drum Near Life Timing] on the touch panel to change the setting. Available values are from 500 to 3,000 (in 500 increments).
Use the numbered markers next to the drum roller to find the mark on the drum. For example, a dot in column 2 on the check sheet means that there is a mark in drum region “2”. Turn the edge of the drum unit toward you while looking at the drum surface to find the mark.
There are many factors that determine the actual drum life, such as the temperature, humidity, type of paper, type of toner used, number of pages per print job and so on. Under ideal conditions, the average drum life is estimated at approximately 12,000 pages.
Most drums in the popular drum kit have a fundamental frequency between 50-250 Hz, depending on their size, what drumheads are used, and how they are tuned.
Laser printers have a drum. A primary charge roller (or in some cases a corona wire) applies between -500 and -1,000 VDC to the imaging drum. This charge neutralizes the photosensitive surface of the drum and prepares it to receive an image.
The drum rolls the toner onto the paper in the form of your print. The toner is melted & pressed onto the paper by heat from a fuser as it passes through its rollers. Your print comes out of the printer.
The toner cartridge contains several components including the color pigment used to create letters and images. The imaging drum is the unit that transfers the toner to paper by following the principles of electrophotography. Not all laser printer models require both toner cartridge and imaging drums.
But the laser printers need the assistance of a photosensitive imaging drum (popularly known as the printer drum), to transfer the fine powders from the toner to the paper.
The Main Difference Between a Drum and Flatbed Plotter
Flatbed plotters hold the paper still while the pen moves, and drum plotters roll paper over a cylinder.
The principal difference of a plotter vs printer is the size of paper they can use. Traditional printers can create large prints comprising multiple sheets of paper. But you can use large rolls of paper with a plotter, allowing for increased accuracy for scaling and ratios.
You can set when to display the “Image Drum Near Life” message. Press [Device Settings] > [Admin Setup] > [User Install] > [Drum Near Life Timing] on the touch panel to change the setting. Available values are from 500 to 3,000 (in 500 increments).
Printer drum repair is an important service that requires knowledge and experience to complete in order to restore your printer. It includes troubleshooting printer drum problems such as HP, Brother and others, cleaning printer drum cartridges, replacing printer drum 88a and buying printer drum cleaning.
You can set when to display the “Image Drum Near Life” message. Press [Device Settings] > [Admin Setup] > [User Install] > [Drum Near Life Timing] on the touch panel to change the setting. Available values are from 500 to 3,000 (in 500 increments).
Description. Image drum is designed for use with Oki Data C330dn, C530dn, MC361 MFP and MC561 MFP. Drum lasts up to 20,000 pages.
The Brother machine will display a `Replace Drum` or `Drum Stop` message when the machine has printed approximately 15,000 pages. The drums should be replaced as a set in order to maintain print quality. Unlike the toner cartridges, the drum change is not automatically detected by the machine when they are replaced.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
image drum message
ANSWER : You don’t have to replace it until it wears enough to affect the print quality. You’ll get spots or stripes. Here you go on a free reset. If you read the thread, someone says the procedure also works on your model. http://www.fixyourownprinter.com/posts/33634
Read Full Q/A … :
Okidata Oki C 5150N
HP 2840 All-in-one ,image drum counter reset
ANSWER : Hi, My HP 2840 is showing replace supplies on all but black , to print color all I have to do is send print command before the printer shows ready and it will print full color , also the windows test print works at any time ? It’s a pain but it works !
Read Full Q/A … :
Okidata Oki C 5150N
reset toners and image drum life
ANSWER : They both have chips that need to be replaced. There are videos on YouTube that show how to refill the toners and how to replace the chips.
Read Full Q/A … :
Okidata Oki C 5150N
replace drum message 100 FPM175 NW
ANSWER : Probably, but without a model number how can anyone help you?
Read Full Q/A … :
Okidata Oki C 5150N
Error message pump motor stalled
ANSWER : Hy,
Read Full Q/A … :
Okidata Oki C 5150N
Error message reads remove and check right cartridge
ANSWER : You can try cleaning the contacts on the back of the cartridge and the ones that they contact in the printer. Other than that, you have to replace the cartridge. I once had one that did the same thing. I swapped the cartridge with another printer of the same model and both printers worked fine. I swapped them back and the original printer got the same error. The other printer had no problem with either cartridge. I swapped them back and left them that way.
Read Full Q/A … :
Okidata Oki C 5150N
Color LaserJet 2500 new drum doesn't work.
ANSWER : The drums have a chip on them and it should have reset when you installed it. If not, then read this thread.
Read Full Q/A … :
Okidata Oki C 5150N
error message
ANSWER : Search it on google
Read Full Q/A … :
Okidata Oki C 5150N