Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Sometimes a paper jam error persists even though there is no jammed paper (false paper jam). Reset the printer, which might clear a false paper jam error, and then try to print again. With the printer turned on, disconnect the power cord from the printer. Unplug the power cord from the power source.
Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer. False paper jams can also occur.
If the paper is even slightly askew, the rollers will pick it up a little crooked, and — guess what — the crooked sheet will immediately get jammed. So even though there`s no paper stuck when you start printing, the loose paper guides are ensuring that a sheet gets jammed whenever the printer starts doing its thing.
If your printer has a paper path cover behind the carriage, remove the cover, and then remove any jammed paper. Pull out the input tray, and then remove any jammed paper. If your printer has a bottom cleanout door, carefully lift the printer and look under it, and then remove any jammed paper from the bottom cleanout.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the rear of the product.
It`s important to replace the drum promptly when it`s low to avoid any further damage to the printer and to maintain optimal print quality. A bad drum may cause paper jams because it can cause the toner to be unevenly distributed on the paper, leading to jams or misfeeds.
This may be caused by pieces of paper or foreign matter in the machine, or paper not loaded correctly.
The optical sensor calibrates the printer to the specific ink cartridges and print heads, which eliminates the need for customers to manually calibrate the printer. The sensor also ensures the printer is properly calibrated to the print head nozzles to deliver optimal print quality.
Common causes of paper jams include: Damaged rollers. Inserting paper that is incompatible with the printer. Loading the paper incorrectly.
Filament jams happen when the extruder can`t push filament through the hot end. The extruder either grinds the filament until it`s so thin that the gear that advances the filament is no longer in contact with it, or the motor that drives the extruder stalls because it`s overloaded.
In screen printing, the premature drying of ink within the fibers of the screen fabric, which prevents ink from flowing through the stencil onto the substrate, producing printing defects such as voids. Also known as drying-in. All text and images are licensed under a Creative Commons License.
Separate drum units last quite a bit longer than a toner cartridge and typically should be replaced after the use of 3-4 toners. Your printer should inform you when it`s time to replace the drum, but you can usually tell your drum is on it`s last legs if you start to see black spots or lines across the page.
When your printer leaves black lines, the lines indicate that there are excess toner powders on the rollers or transfer belt within the printer. As the paper is moved along by the rollers and transfer belt, any excess powder left on them can result in lines being left on the paper.
Remove the toner cartridge and gently wipe to remove any dust or toner underneath with a dry cloth. If you notice excess toner inside the print device, it may be possible to remove it using a vacuum that is specifically designed to capture fine dust particles like toner powder. These vacuums can be costly, however.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.

Read Full Q/A … :
Unknown Printer

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :
Unknown Printer

Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳

Read Full Q/A … :
Unknown Printer

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :
Unknown Printer

Keep getting a paper jam message. There is no jam.
ANSWER : You can quit wondering. Parts are unavailable. I’ve seen posts where people have 3D printed the parts or machined them out of metal.

Read Full Q/A … :
Unknown Printer

Paper jam in tray 2 (but no paper pulled from tray) also M476DN models
ANSWER : Isopropyl alcohol is not recommended for rubber rollers. It dries out the rubber and hasten it’s cracking and breaking. It will do nothing to restore the grip. Those rollers are really hard to replace. It would be easy if that dumbass secondary menu really worked. None of the techs I’ve spoke to ever got into it. Everyone I know sends a print job and listens for the roller to rotate into position where you can pull it off.

Read Full Q/A … :
Unknown Printer

message error: ADF paper jam
ANSWER : There is a thin plastic arm that the paper pushes on. It is spring loaded. If it doesn’t return and unblock the sensor after the paper passes it, you get the paper jam warning. I’m guessing that is the spring you are referring to.

Read Full Q/A … :
Unknown Printer