HPLJ 4600DN

Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Restart the printer and the computer or mobile device to clear possible error conditions. Restore Wi-Fi setup mode. Most printers with a touchscreen display or menu: Open the Wireless or Setup menu, select Network setup or Settings, and then select Restore Network Settings.

Any of these error codes (51.2c , 51.2m , 51.2y , 51.2k) points to a failure with one of the laser scanner assemblies on the HP Color LaserJet 4600 series. To solve this error code, replace the corresponding laser scanner.

The error is indicating that there is a Magenta Laser problem that needs to be resolved by service. You will need to contact an HP-authorized service or support provider.

Check cables or wireless connection

Make sure that the printer`s USB cable is properly connected from the printer to your PC. If your USB isn`t recognized, see Automatically diagnose and fix Windows USB problems. Check the wireless connection (for wireless printers).

Restart the printer and try again. Unplug the printer from an outlet. You can plug it back in again to see if it works this time. Check if the printer is properly set up or connected to your computer`s system.

This error is primarily caused by a transfer alienation failure in which the ITB is stuck and unable to rotate, the SR9 sensor (the primary transfer roller disengagement sensor) has gone bad or the fuser drive assembly has failed.

57.1 , 57.3 , 57.4 , 57.5 , 57.6 , 57.7 , 57.8 Error HP LaserJet 9000 9040 9050. Any of the 57 errors on the HP LaserJet 9000 , 9040, and 9050 series printers are fan errors. There are 7 fans in the machine. Replacing the corresponding fan usually cures these errors; fans are a common failure part on this model.

If the error code 33.05 is displayed once inserting the eMMC and or replacing the Printer`s Formatter, an updated firmware must be performed. The printer may broad cast this error along with the “Security Alert” message.

Open Control Panel > Hardware and Sound > Devices and Printers. Right-click the printer and select Properties. Look in the Web Services tab for your IP address if only three tabs appear. Alternatively, look in the Ports tab for your IP address if five tabs appear.

Wi-Fi printers

Go to the Start menu and click Settings, Devices, then Printers & scanners. Select Add a printer or scanner and wait for your printer to appear in the list, then select it and hit Add device. If Windows doesn`t find your printer, select The printer that I want isn`t listed and follow the instructions.

Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.

The Print Spooler is software built into the Windows operating system that temporarily stores print jobs in the computer`s memory until the printer is ready to print them. In some circumstances you may need to stop and/or restart the service.

The 59. F0 has been a common error code on the HP CLJ M452 and M377 / M477 MFP models. The printers service manual references this error to a “drum motor assembly” but in most cases has been resolved by replacing the Transfer Belt assembly (RM2-6454).

Description: This error is primarily caused by a transfer alienation failure in which the ITB is stuck and unable to rotate, the SR9 sensor (the primary transfer roller disengagement sensor) has gone bad or the fuser drive assembly has failed.

In Windows, search for and open Add a printer or scanner . Click Add a printer or scanner, and then wait for Windows to locate available printers. If your printer is found, click it, and then click Add device to complete the driver installation.

A specific print job that is not correctly formatted for the printer or that is not correctly processed by it can trigger a 79:04 system error.

99.09.62 – Unknown Disk

This error indicates there is an encryption mismatch between the HDD and the formatter. This typically happens because an HDD was swapped into a device from another device or replaced. Resolution: If the HDD is in the device by error, remove it and return it to its original device.

41.02 error on this printer is a laser/scanner error. If the message does not clear, then you need to replace the laser/scanner. If you are not getting a 41.02 error, then report back with the correct number. The 05 does not mean anything.

Verify that the toner cartridge and the transfer roller are seated correctly. Ensure that the tray pickup, feed, and separation rollers are installed correctly and show no damage or wear. Check if the rollers are installed correctly.

Connect the printer power cord to the printer and turn the printer back on. Disconnect the power cord from your wireless router. Wait 10 seconds before reconnecting it. It may take a few minutes for your internet to come back on.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

hplj 4 stops working after being on for 5 minutes

ANSWER : Those are some strange symptoms. I would kind of suspect the culprit is the DC controller. The accordion jam is another issue. That is caused by the 2 exit rollers. They get glazed from age and aren’t able to push the paper out and it accordions because the fuser is still pushing it out and there’s nowhere for it to go.

Read Full Q/A … :
Unknown Printer

HPLJ 4200 54.1 error

ANSWER : Can you please send me the link

Read Full Q/A … :
Unknown Printer