HP LaserJet IIIP+
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
yz Fuser error To continue turn off then on is displayed on the control panel, it indicates that there is an issue with the fuser. The XX and YZ are two digit codes that provide information on the specific issue causing the error. Press the power button to turn the printer off, and then back on to clear the error.
If you have NOT recently replaced the fuser or moved the printer around, then the 50.2 fuser error indicates you may have an actual fuser failure and the fuser needs replacing.
A high fuser temperature error has occurred. Note: A fuser error might occur because of inadequate power supply, inadequate line voltage, or a fuser problem.
Error 50.8 suggests one end of the fuser is not heating up which may be damage to the sleeve or heavy media.
Error 50 is Invalid destination number.
Error code 50 indicates your Mac could not copy or move files from external storage devices. The whole process gets stuck with no visible progress.
50.2 error indicates that the printer is not heating up fast enough. This can be caused by a bad heating element in the fuser but can also be caused when the printer does not have adequate power due to overloaded circuits or being plugged into a power strip or surge bar that limits current flow.
50.AF is a low fuser temperature error and usually caused by a defective fuser. Resetting the printer is unlikely to resolve this error.
If you see this error code 50.5 on an HP LaserJet 4200, 4240, 4250, 4300, or 4350 series printer, the fuser installed in the printer is registering as an incorrect fuser for that model printer.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
If you have NOT recently replaced the fuser or heavily jostled the printer around, then the 50.7 Fuser error indicates you have an actual fuser failure (the gearing pressure is not releasing) and the fuser needs replacing.
Look inside the fuser opening to make sure there is no debris or jammed paper. Remove any debris or jammed paper, if found. Hold the handles on each side of the fuser and reinstall it in the printer.
Just find the menu “APN setting” and re initialze it. Reboot. Then, it should work. If not, you`ll have to see with your carrier.
Re: Sky Go app on iPad error 50-2 code
Are you at home and connected to your Wifi connection when this error appears, if so try disabling the Wifi on your device and then enable it again after a few minutes. If someone has helped you then please click on the LIKES button in their post.
Code 50 = Memory initialization error.
Error code 50 occurs if the system is unable to back up existing assets while installing.
When a 50.4F. 00 error is displayed on the control panel, it indicates that there is an issue with the fuser or the power outlet where the printer is connected. Turn the printer off, and then back on to clear the error. Ensure that the power outlet, to which the printer is connected, is in good working condition.
The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.
On the HP LaserJet P3015 P3015n and P3015dn series printers, this 51.00. 10 error code may be temporary. Try turning the printer off and back on to see if the error clears. If the error comes back repeatedly, you have a failing laser scanner assembly which requires replacement.
I found the following: Error 50 means that the heating of the fuser unit is no longer working. This is usually a burnt-out heating lamp,or a defective thermal fuse.
If you see this error code 50.5 on an HP LaserJet 4200, 4240, 4250, 4300, or 4350 series printer, the fuser installed in the printer is registering as an incorrect fuser for that model printer.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
Turn off the HP printer and unplug it from the power source. Also, shut down your computer and unplug any external devices. Wait for a few minutes and then plug in the printer and turn it back on. Finally, turn on your computer and check if the error state has been resolved.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
error 50
ANSWER : Most likely the quartz lamp in the fuser assy. burned out. you can remove it and check the resistance on the 2 large pins in the connector. Should be several ohms.
Read Full Q/A … :
HP LaserJet IIIP+
can i override the error code 50
ANSWER : First off, your printer is an inkjet printer. It has no drum. The error refers to a paper jam.
Read Full Q/A … :
HP LaserJet IIIP+
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
HP LaserJet IIIP+
Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.
Read Full Q/A … :
HP LaserJet IIIP+
Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.
Read Full Q/A … :
HP LaserJet IIIP+
HP 9040 MFP Error code
ANSWER : bonsoir
Read Full Q/A … :
HP LaserJet IIIP+
HP CLJ CP 5225 ERROR 55.0601
ANSWER : my printer cp5225 is giving me error code 55.0601 message which i can’t fix please help
Read Full Q/A … :
HP LaserJet IIIP+
Scanner error keeps coming up
ANSWER : I am having the same problem with my Epson Workforce 645
Read Full Q/A … :
HP LaserJet IIIP+