HP LaserJet 4300

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Open the front door on the printer. Remove the toner cartridge from the printer. Lift the jam-access cover and slowly remove any jammed paper. Be careful not to tear the paper.
Sometimes a paper jam error persists even though there is no jammed paper (false paper jam). Reset the printer, which might clear a false paper jam error, and then try to print again. With the printer turned on, disconnect the power cord from the printer. Unplug the power cord from the power source.
If the paper is even slightly askew, the rollers will pick it up a little crooked, and — guess what — the crooked sheet will immediately get jammed. So even though there`s no paper stuck when you start printing, the loose paper guides are ensuring that a sheet gets jammed whenever the printer starts doing its thing.
Open the front cover and remove the paper. Pull Front Cover Open Lever, and then open the front cover with both hands carefully. Carefully pull the jammed paper upward and out. If paper has jammed inside the transfer unit, holding both sides of the paper, pull the paper carefully forward and out.
Step one: Perform a power reset

With the product turned on, disconnect the power cord from the rear of the product. Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet.

Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

HP LaserJet 4300

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :

HP LaserJet 4300

Paper jam in tray 2 (but no paper pulled from tray) also M476DN models
ANSWER : Isopropyl alcohol is not recommended for rubber rollers. It dries out the rubber and hasten it’s cracking and breaking. It will do nothing to restore the grip. Those rollers are really hard to replace. It would be easy if that dumbass secondary menu really worked. None of the techs I’ve spoke to ever got into it. Everyone I know sends a print job and listens for the roller to rotate into position where you can pull it off.

Read Full Q/A … :

HP LaserJet 4300

Tray 1 (upper tray) paper feed problem
ANSWER : There is no way of adjusting the distance of lift. Could be that the pickup roller is worn enough that it will pick up a sheet that is higher, but not one that is lower down. You can look at the end of the roller that first makes contact and see if it is worn smooth.

Read Full Q/A … :

HP LaserJet 4300

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :

HP LaserJet 4300

Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.

Read Full Q/A … :

HP LaserJet 4300

Paper Jam Tray 1
ANSWER : Tray No. 1 (the feeder) has to be either FULLY closed or FULLY down, down to about a 45 degree angle. Then hit the OK button and it should Initialize and start working. This solution is for when there is actually NO paper jamming the printer.

Read Full Q/A … :

HP LaserJet 4300

Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳

Read Full Q/A … :

HP LaserJet 4300