HP LaserJet 4250
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
At times, a related message such as a “13.01 Paper Jammed in Tray 2” which indicates that the paper did not arrive at the pre-feed sensor (PS102) in the amount of time allotted by the DC Controller. There may also be other messages such as the “13.20 Jam In Top Cover Area” or the “13.03 Paper Jam”.
00 Jam in Top Cover Area Error on HP LaserJet 4200 or HP LaserJet 4300 series. If you see this error code 13.20. 00 “Jam in Top Cover Area” on either an HP LaserJet 4200 or HP LaserJet 4300 series printer, the printer either has a sensor blocked or it has an incorrect model fuser installed.
41.2 Error Code on HP Laser Printers
The arcing occurs in the toner/transfer area, and can be caused by a defective toner cartridge, bad high voltage or ground connections to the toner cartridge or transfer roller, or a defective high voltage power supply.
50.2 error indicates that the printer is not heating up fast enough. This can be caused by a bad heating element in the fuser but can also be caused when the printer does not have adequate power due to overloaded circuits or being plugged into a power strip or surge bar that limits current flow.
It means the top of the paper isn`t being detected arriving at the fuser delivery sensor.
The 13. A4. D4 indicates that there is a “paper delay” jam in Tray 4. Which means that paper did not reach SR8 (sensor 8) in the allotted time necessary after the start of paper pickup from Tray 4.
If the sensor is not cleared in a specified time a 13.20 paper jam message is displayed. Remember that this may mean there is media in the paper path, or one of the paper jam sensors is failing. cleared from the paper path.
A piece of paper stuck in the paper tray or inside the printer can create a paper jam. Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer.
A 13. B2. FF paper jam error appears on the control panel when paper is jammed in the top of the printer. Check the printer for jammed paper and clear the jam, if needed.
If you see this error code 50.5 on an HP LaserJet 4200, 4240, 4250, 4300, or 4350 series printer, the fuser installed in the printer is registering as an incorrect fuser for that model printer.
That error code indicates a failure of the yellow laser scanner. Unplug and leave for a few minutes, also make sure you are plugged directly into the wall and not into a surge protector.
This means the baud rate is 9600 7 E for both the scanner and scale. If one tries to configure this Dual Cable device to a Single Cable device via bar codes it will beep once, reading the bar code, then emit a razz tone and throw an Error 13.
This error indicates paper in the path at power-on or after a door is closed. All jam Errors ending in “FF” are residual jam errors which means there was paper or debris still in the printer after a printer was powered on or a door was opened and closed.
Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.
Very often a 13.1 Paper Jam Message will appear, instructing the user to check Tray 2 or to check under the toner cartridge. Upon thoroughly checking the printer there is no paper jam to be found anywhere.
This jam occurs when residual paper is detected at the Tray 2 feed sensor (SR11). Open Tray 2, remove any jammed paper, and then close the tray. Open and close the upper right door to allow the printer to attempt to clear the jam.
Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.
This means the baud rate is 9600 7 E for both the scanner and scale. If one tries to configure this Dual Cable device to a Single Cable device via bar codes it will beep once, reading the bar code, then emit a razz tone and throw an Error 13.
Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.
This means the baud rate is 9600 7 E for both the scanner and scale. If one tries to configure this Dual Cable device to a Single Cable device via bar codes it will beep once, reading the bar code, then emit a razz tone and throw an Error 13.
According to technical documentation this error is usually caused when trying to print on a unit that had either an internal or external finisher and that device has been removed, without replacing the flag assembly that is used for standard output bin.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
HP LaserJet 4250
Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.
Read Full Q/A … :
HP LaserJet 4250
Scanner error keeps coming up
ANSWER : I am having the same problem with my Epson Workforce 645
Read Full Q/A … :
HP LaserJet 4250
HP CLJ CP 5225 ERROR 55.0601
ANSWER : my printer cp5225 is giving me error code 55.0601 message which i can’t fix please help
Read Full Q/A … :
HP LaserJet 4250
Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.
Read Full Q/A … :
HP LaserJet 4250
HP 9040 MFP Error code
ANSWER : bonsoir
Read Full Q/A … :
HP LaserJet 4250
Density Shutter Error
ANSWER : I’ve never worked on one of those printers, but I have never, ever seen 1 valid solution for printer repair on fixya.com I read the replies there when I need a good laugh. Makes me wonder what the “techs” on that forum actually do for a living. It certainly couldn’t be printer repair.
Read Full Q/A … :
HP LaserJet 4250
52.0 SCANNER ERROR
ANSWER : Laser scanner assembly.
Read Full Q/A … :
HP LaserJet 4250