HP3si

An Er/03 error message indicates the printer failed to pick a sheet of paper to print. Remove the stack of paper from the tray and check the condition of the paper. Reload the paper, and then try to print, copy or scan.

An Er/04, Er/05, or Er/06 error message indicates a paper jam. Find and clear the printer of any jammed paper, or reset the printer if the printer has no jammed paper.

Er/61 displays, the Wireless button is amber, and the Cancel button is blinking. An error occurred during Wi-Fi Protected Setup (WPS) and the printer was not able to connect to the network. to clear the error, and then try again. For more information and wireless troubleshooting steps, go to Wireless Printer Setup.

P2 error indicates — An ID Copy job has been started. Fix — Turn over the identification card and press the ID Copy button to continue. Perform a power reset , Reset the printer to recover from printer errors or failures.

Error Code 3 is a Windows error code that appears when the computer cannot find the specified path.

The E3 error code indicates the unit has detected there is no refrigerant. The unit will require a repair service for refrigerant to be added, please visit Request a Repair page for further assistance.

Paper Jam in Input Tray.

An E3 or E4 error indicates a carriage or paper jam.

Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.

That error code indicates a failure of the yellow laser scanner. Unplug and leave for a few minutes, also make sure you are plugged directly into the wall and not into a surge protector.

A 13. C3. A2 paper jam error appears on the control panel when paper is jammed before it exits the printer, or as it enters the stapler/stacker. Check the printer for jammed paper and clear the jam, if needed.

An E9 error occurs when the printer detects that ink system maintenance is required. An Ink System Maintenance page prints containing instructions to open and close the printhead access door to resolve the error.

16-3 errors can be caused by attempting to view recordings on multiple devices simultaneously. Remember, you can only play back recordings from your AirTV on one device at a time. Stop playback on one device to continue watching on another.

What Is Error Code 5 Chrome? Chrome Error Code 5 occurs when there`s an issue with the SSL protocol – specifically, when the server is unable to recognize a secure connection from your browser. The most common cause of this problem is that the server isn`t configured properly for Secure Sockets Layer (SSL) connections.

It could be your encoder strip and/or encoder strip sensor. If it is not the motor, then usually the encoder is at fault for that code. Hope that helps and good luck.

(Code 3)” The device driver may be corrupted, or you are runningout of memory; the system is running low on system memory and may need to free up or add more memory. If the computer has insufficient memory to run the device, you can close some applications to make memory available.

E3 indicates a combined water outlet temperature sensor error. E4 indicates a water outlet temperature sensor error.

HP Printer Error E4 means that the FINE cartridge in your printer device is not installed appropriately. To move out the cartridges, you will require to push the output tray back in before opening the cover.

The 13. A4. D4 indicates that there is a “paper delay” jam in Tray 4. Which means that paper did not reach SR8 (sensor 8) in the allotted time necessary after the start of paper pickup from Tray 4.

If the trigger cannot be fully inserted, the door is not properly closed and the E02 or E03 error will occur. To resolve this error, you need to ensure that the printer cable is long enough to allow the door trigger to be fully inserted.

Go to Solution. This error indicates a RAM failure. The specific memory is internal memory not one of the dimm slots. You can try removing any additional memory first to see if the device will boot but likely this is a failure of the formatter and you would need to replace the formatter.

If the trigger cannot be fully inserted, the door is not properly closed and the E02 or E03 error will occur. To resolve this error, you need to ensure that the printer cable is long enough to allow the door trigger to be fully inserted.

Go to Solution. This error indicates a RAM failure. The specific memory is internal memory not one of the dimm slots. You can try removing any additional memory first to see if the device will boot but likely this is a failure of the formatter and you would need to replace the formatter.

Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.