HP Color LaserJet 3700DN

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

59. C0 = Developer motor rotation error. With this printer it usually means the product needs to be replaced. What you can try is to remove all toners and then start up the printer and see if the error appears.
Description: Printer boots up to 59. F0 Error and is unable to print. This error is primarily caused by one of the following conditions: A transfer alienation failure in which the ITB is stuck and unable to properly engage the internal transfer rollers.
In most cases, this is a problem with a fuser motor transmission.
Check for excessive wear on gears in Main Drive Assembly

An issue was identified with the material in one of the gears in the Main Drive Assembly for some of the early production units. This issue would cause excessive wear on the gear that eventually results in a 59.0C/59.00. C0 error.

For a 59. F0 error, generally we recommend you try reseating the transfer belt assembly a couple times, also try reseating the toner and the fuser assembly. If you have spares of any of these parts you can install them to help eliminate culprits. The problem can be a failing Transfer Belt Assembly.
59 error including loud noise followed with a poor print quality and toner cartridge coming out of its position, and/or toner access door starts to open by itself. Source of all above-mentioned symptoms is a bent metal ( U shaped) shaft that is used to lock toner cartridge in position for printing.
The 59. F0 has been a common error code on the HP CLJ M452 and M377 / M477 MFP models. The printers service manual references this error to a “drum motor assembly” but in most cases has been resolved by replacing the Transfer Belt assembly (RM2-6454).
F0 error upon powering up a HP Color LaserJet CP3525 printer or CM3530 MFP? There are two possible causes for the 59. F0 error: either the transfer belt is stuck or otherwise unable to rotate, or Sensor SR17 is not working.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
Apparently, a bad toner cartridge can cause error 59.00. 30, but replacing the toner combined with: removing the fuser and putting some oil on the axis at each end (and turning the gear several revolutions), cleaning the paper path and rollers solved the problem.
`Operation could not be completed (error 0x00000709) Double check the printer name and make sure that the printer is connected to the network. Hi, It`s a known issue in Windows 11 22H2. This error occurs because the default connection method has changed in 22H2.
10.10 Supply Errors

When you put in a toner cartridge and the printer comes up with a 10. 10 Supply Memory Error, this means there is a problem with the chip in your toner and we need to issue you a replacement.

90 or 59.00. A0 Error resulting from a registration assembly and/or paper feed assembly that is jammed/stuck.
59.70 is a black developer motor failure. If unit is still under warranty contact tech support and get it repaired. If unit is out of warranty you will need a developer motor RM2–7344–000CN.
This error is a motor error. The C0 probably refers to the alienation motor. Replacing the alienation motor may resolve your issue. If not maybe there is a damage in your main gear assembly.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
The 59. F0 has been a common error code on the HP CLJ M452 and M377 / M477 MFP models. The printers service manual references this error to a “drum motor assembly” but in most cases has been resolved by replacing the Transfer Belt assembly (RM2-6454).

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :

HP Color LaserJet 3700DN

newly installed printer…can scan but cant be set as a default printer???
ANSWER : ITS AN EPSON L210…

Read Full Q/A … :

HP Color LaserJet 3700DN

Difference Between Laser Printer and InkJet Printer
ANSWER : Laser uses toner which is a powder that gets melted onto the page. Inkjet uses ink that gets squirted onto the page.

Read Full Q/A … :

HP Color LaserJet 3700DN

Printer error Oxc18a0201
ANSWER : Have no idea what model you have, but try this forum post or search through the site using your model and error.

Read Full Q/A … :

HP Color LaserJet 3700DN

canon printer error
ANSWER : Here are the procedure to fix Canon smartbase MP730 printer error ##334

Read Full Q/A … :

HP Color LaserJet 3700DN

PRINTER MX 320 CANON ALL IN ONE PRINTER
ANSWER : Probably a worn feed roller. You can try cleaning it with a damp rag as it might just be covered with paper dust.

Read Full Q/A … :

HP Color LaserJet 3700DN

printer error fix
ANSWER : Epson 2540

Read Full Q/A … :

HP Color LaserJet 3700DN

Canon i255 printer head error
ANSWER : Sometimes the print head issues are brought on not by a flawed print head but rather by a “gunky” stopping station. The stopping station is the spot where the print head “rests” when it is not printing. Generally it’s on the right half of the printer (taking a gander at the printer from the front). The stopping station has elastic seals that should encompass the print head when it’s stopped.

Read Full Q/A … :

HP Color LaserJet 3700DN