HP LaserJet 2430

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Clean the rollers inside the printer, and then try to print again.
Check inside the printer for any debris that might be causing paper jams. Turn off the printer, and then unplug the power cord from the electrical outlet. Remove any paper from the input tray. Open the rear access door, and then clean the paper feed rollers with a lint-free cloth lightly moistened with filtered water.
00 Jam in Top Cover Area Error on HP LaserJet 4200 or HP LaserJet 4300 series. If you see this error code 13.20. 00 “Jam in Top Cover Area” on either an HP LaserJet 4200 or HP LaserJet 4300 series printer, the printer either has a sensor blocked or it has an incorrect model fuser installed.
This can happen for a variety of reasons, from a sudden power outage, low ink, no paper, a paper jam to interference by third-party firewall software.
If your printer keeps jamming, you should know that the most common cause of a jam is misalignment of the paper. Paper needs to load in smoothly, completely flush with the tray. Overfilling the tray is a great way to ensure you will be spending some personal time getting to know the inside of a printer.
A paper jam is when paper or other printed material gets stuck or lodged in a printer and cannot eject.
The above listed printers may produce a 13.20. 00 `jam in right front door` error code. While there may be no paper visible, this is usually caused by a dislodged tray 1 pickup roller cover which disrupts proper positioning of the duplex refeed sensor flag.
It means the top of the paper isn`t being detected arriving at the fuser delivery sensor.
Hold jammed paper firmly in both hands. If the paper is rolled up, pull out it. Slowly pull out paper, so as not to tear it. Pull out the paper at an angle of about 45 degrees.
Step one: Perform a power reset

Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the rear of the product.

This is one of the most common causes of paper jams. Loading paper that is stuck together, frayed, curled or bent can cause a jam. Overloading the paper tray, loading different thicknesses of paper in the tray or using paper that isn`t appropriate for your particular printer can all result in a jammed printer.
Did you know most copier paper jams are caused by the paper itself? Misaligned paper. When a stack of paper isn`t aligned properly in the machine, it often causes a paper jam issue. When adding a ream of paper, always fan the paper, load carefully and avoid overstuffing the tray.
Common locations of paper jams in laser printer include paper input and output trays, the fuser, the toner cartridge, and any other place that paper comes into contact with a roller.
The error is 13.02. 00 indicating it isn`t reaching the top cover sensor. The paper is getting stuck at the fuser, and the fuser is leaving a very noticeable indentation mark.
Slowly pull out paper, either from paper output slot or from rear tray, whichever is easier. Hold the paper with both hands, and pull it out slowly so as not to tear it. If you cannot pull out the paper, turn the printer back on without pulling forcibly. The paper may be ejected automatically.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :

HP LaserJet 2430

jamming with no actual jam
ANSWER : I usually watch the pickup roller action through the opening at the back of th.e tray. That will give you some idea of why it isn’t feeding

Read Full Q/A … :

HP LaserJet 2430

Keep getting a paper jam message. There is no jam.
ANSWER : You can quit wondering. Parts are unavailable. I’ve seen posts where people have 3D printed the parts or machined them out of metal.

Read Full Q/A … :

HP LaserJet 2430

Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳

Read Full Q/A … :

HP LaserJet 2430

Printer jammed, after jam clearance there is an error message
ANSWER : I am looking for steps to isolate this issue. I don’t suspect the formatter.

Read Full Q/A … :

HP LaserJet 2430

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :

HP LaserJet 2430

Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.

Read Full Q/A … :

HP LaserJet 2430

P2055dn Duplex Jam – Jam in Output Bin
ANSWER : I have same problem on duplex of 2nd page. Paper stops just behind Tray 1 pickup roller. Noted there is a small black 1/2″ lever tab behind the lower rear jam door. Noting that when printer jams trying to finish 2nd side, the lever is down ??? No answer, I know, just observation & looking for mention of this by someone. Going to try and find a black or white sensor which may be out of position.

Read Full Q/A … :

HP LaserJet 2430