HP LaserJet 2410

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
If you are having trouble getting your cartridge to read properly or are having connectivity issues with your printer, sometimes a hard reset will resolve the problem. Power down the printer and then unplug the power cord from the printer and the wall. Wait for a minute, then plug the printer back in.
Press the button on the chip-reset tool for several seconds until the LED light on the device goes off. Then, unlock the reset tool from the cartridge. Use the resetter with other cartridges and install them back into the corresponding slots in your printer. Voila!
To be specific, you should make sure that your printer has sufficient paper, ink or toner and without paper jam. If the printer cartridge`s status is faulty, you should replace it with a new one. After carrying out these operations, check if the HP printer can print properly. If not, try other methods immediately.
On HP printers, a “cold reset” causes the printer to return to its factory default settings, which among other things, causes it to try and retrieve its configuration information from a BOOTP server. This is how SAP printers and Athena printers should receive their configuration information.
An E1 or E2 error indicates the paper size setting does not match the paper size loaded in the input tray. Load the correct size paper or change the print settings, and then press the Cancel button .
A new page should print with a claim code. If the page does not print, see the email address on the printer display. The first part of the HP ePrint address preceding “@hpeprint.com” is the claim code. For example, if your HP ePrint email is “[email protected]”, then “abc” is your claim code.
1: Check Printer Power, Cables, and Paper

Check that the correct paper is properly loaded into the printer and is not jammed. Replacing damaged cables, plugging in loose or disconnected cables, and fixing paper jams as necessary may resolve the issue.

a misprint or misspelling in a text.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
Your printer may not recognize the new ink cartridge, or the ink counter may read it as empty. Many printers have a cartridge reset feature that forces the machine to recognize the cartridge as new.
Verify the ink cartridge(s) is inserted properly. Some cartridges snap in place, and if they are not inserted fully, the printer won`t print anything. If a lever is moved from its original position to allow for installation of ink cartridges, ensure it is returned to its original position.
Reasons why your HP printer has ink but won`t print

This may seem obvious, but it sometimes happens: first make sure your paper tray has paper in it. Misalignment, clogged printheads, faulty data communication or insufficient ink levels can also be sources of the problem.

There are numerous possible causes for a printer that`s randomly producing blanks. The most common ones are empty ink cartridges, improper cartridge installation, and congested nozzles. Driver and software issues can sometimes cause this problem as well.
A cold restart, hard reboot or hard reset can help to get back in to a PC or other device that has completely locked up. A cold restart forces your device to start up from scratch. You will lose any unsaved work, however it may be your only way to recover from some errors.
Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.
An E1 or E2 error indicates that the paper size setting does not match the paper size that is loaded. Remove all paper from the input tray, and then load the correct paper size. Remove any paper from the input tray. Slide the paper width guide as far as possible to the left.
During a print job, the ink cartridge carriage stalls in the printer, and a Carriage Jam or E3 error displays on the printer control panel.
Wipe the sensor window with one of the cotton swabs provided in the Printer Cleaning Kit, slightly dampened (not soaked) with isopropyl alcohol, to remove dried ink. If the sensor window is heavily coated with dry ink, you may need to apply some pressure while wiping, helping the cotton to absorb the ink.
From the printer website, find the Web Services menu, and then click Print Info Page or Print Information Sheet. Find the Printer Code or Printer Claim Code on the page that prints. If the information page only has the printer`s email address, remove and then re-enable Web Services.
Select Start , then select Settings > Devices > Printers & scanners . Scroll down to Related Settings and select Print server properties. Select the Drivers tab, and see if your printer is listed. If it is, you`re all set.
If you are having trouble getting your cartridge to read properly or are having connectivity issues with your printer, sometimes a hard reset will resolve the problem. Power down the printer and then unplug the power cord from the printer and the wall. Wait for a minute, then plug the printer back in.
One sensor is located in the printer carriage. A second sensor—the Auto Sense sensor—is located in the back of the printer near the paper `clean out` area. Each sensor performs a specific set of media detection functions.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP PSC 2410 clicking noise problem
ANSWER : I have the same issue… I’ve tried everything above… I don’t believe it’s dust as this happens on and off occasionally… I think I may need to make a youtube video of me “fixing” this printer! I’m really frustrated with this thing!! If it doesn’t work soon, I’m gonna by the solution in the form of a hammer!

Read Full Q/A … :

HP LaserJet 2410

HP PSC 1510 copying problems
ANSWER : my hp photocopy is not working

Read Full Q/A … :

HP LaserJet 2410

HP PSC 2410 Carriage Jam
ANSWER : Hi All,

Read Full Q/A … :

HP LaserJet 2410

HP psc 2110 all-in-one won't turn on after power o
ANSWER : left the printer on now i cant get the printer to go on

Read Full Q/A … :

HP LaserJet 2410

HP PSC 1210 Service Manual?
ANSWER : Hi Abe,

Read Full Q/A … :

HP LaserJet 2410

HP PSC 1610 – problem installing hardware
ANSWER : If you want to get proper detailed information about hp printer then you should call on 1-888-924-2961 toll free number. They provide you step by step methods of installation process and driver support services.

Read Full Q/A … :

HP LaserJet 2410

HP PSC 2510 all-in-one network setup problems
ANSWER : Assemble the accompanying things:

Read Full Q/A … :

HP LaserJet 2410

HP psc 1210 Wont Feed Paper
ANSWER : This printer seems to have special problems with paper feed asy. When functioning works

Read Full Q/A … :

HP LaserJet 2410