HP Photosmart 8750

Experienced technical support provide their insights in answering this question :
I had this error after the printer sat idle for many months. I thought it was the cartridge drive belt stretching, because it was extremely loose and wouldn’t move the carriage due to slippage. Then I noticed there was a gear belt tensioner to the right side that had some movement. Sure enough, when I shined a flashlight into the ink reservoir, there was a spring that had fallen down inside. Looking at the plastic belt tensioner, it looks as if the spring was held on by a plastic post that had broken off. This is most likely the cause of many of these errors, because the plastic break is very clean and not readily visible, (a design flaw in my opinion). Rather than trying to replace the part, I am going to try tapping a hole in the plastic and inserting a machine screw that can hold the tension spring in place. It also looks like the metal notch for the right hand loop of the spring, would not prevent the spring from slipping off at some point, so using a metal file to enlarge the notch may be necessary. If you’re lucky, your spring may have just popped off and is inside the ink reservoir. This may be one reason why the printer was discontinued so soon. One lousy five dollar part makes the whole printer worthless… I use this this printer primarily because it is easy to clean the heads by removing the carts, instead of having to disassemble the whole damn thing, as in ink tank designs. It makes beautiful 13×19 prints with better color accuracy than my Vivera 6 ink printer.

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Clean the rollers inside the printer, and then try to print again. Disconnect the power cord from the back of the printer. Press in the tab on the left side of the rear door to release the door.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
A piece of paper stuck in the paper tray or inside the printer can create a paper jam. Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer.
Low-quality paper leaves an accumulation of tiny paper bits often referred to as “paper dust” inside the machine. This “dust” is one of the top causes of paper jams. More dust means more jams. Besides jams, the dust also contributes to poor-quality prints and causes machine parts to wear at a faster rate.
Sometimes called a forced reset, this allows you to clear the memory if Windows or other software are unresponsive or if there are problems with the display or the computer. Performing a Hard or Forced Reset on Your HP Notebook (Fixed Battery)
Turn the printer off then back on. If the issue persists, turn the printer off, unplug the power cord and then wait at least three minutes before plugging the power cord back in and turning the printer back on. If the issue persists, ensure the product is running the latest firmware available from HP.com.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Wipe the sensor window with one of the cotton swabs provided in the Printer Cleaning Kit, slightly dampened (not soaked) with isopropyl alcohol, to remove dried ink. If the sensor window is heavily coated with dry ink, you may need to apply some pressure while wiping, helping the cotton to absorb the ink.
This can happen for a variety of reasons, from a sudden power outage, low ink, no paper, a paper jam to interference by third-party firewall software.
A paper jam is when paper or other printed material gets stuck or lodged in a printer and cannot eject. When this occurs, the printer does not function properly until the paper is manually removed.
If your printer keeps jamming, you should know that the most common cause of a jam is misalignment of the paper. Paper needs to load in smoothly, completely flush with the tray. Overfilling the tray is a great way to ensure you will be spending some personal time getting to know the inside of a printer.
Retrieve the recovery key from your Microsoft account

Sign into your Microsoft account and retrieve your recovery key. Sign in from the Microsoft recovery key page. Using another computer or mobile device, go to https://windows.microsoft.com/recoverykey (in English).

Reset. Resetting the printer stops printing and clears the current print job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully.
On HP printers, a “cold reset” causes the printer to return to its factory default settings, which among other things, causes it to try and retrieve its configuration information from a BOOTP server. This is how SAP printers and Athena printers should receive their configuration information.
Usually, it should not take more than a few minutes to restore the printer to its factory settings. However, I recommend you to perform the following steps to isolate the issue and arrive at a fix: Disconnect the power cable from the printer while the printer is still ON.
One sensor is located in the printer carriage. A second sensor—the Auto Sense sensor—is located in the back of the printer near the paper `clean out` area. Each sensor performs a specific set of media detection functions.
Select Start , then select Settings > Devices > Printers & scanners . Scroll down to Related Settings and select Print server properties. Select the Drivers tab, and see if your printer is listed. If it is, you`re all set.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
Right! Yes I believe it does. highlight all the jobs and delete, some may still be held so just go into services and restart the spooler. highlight all the jobs and delete, some may still be held so just go into services and restart the spooler.
With the printer turned on, disconnect the power cord from the rear of the printer and also unplug the power cord from the wall outlet. Remove USB cable, if present. Wait for 2-3 minutes, press and hold the power button on your printer for about 30 seconds to remove any additional charge.
– Press and hold down the power button for as long as 60 seconds to drain flea power or excess voltage. – Keep in mind that the device should remain in an off state throughout the process of static discharge.
Your BitLocker recovery key is a unique 48-digit numerical password that can be used to unlock your system if BitLocker is otherwise unable to confirm for certain that the attempt to access the system drive is authorized.
On most phones, you can reset your phone through the Settings app. If you can`t open your phone`s Settings app, you can try factory resetting your phone using its power and volume buttons. We recommend checking your manufacturer`s support site for device-specific instructions.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP Photosmart 8750 intermittent serv. stat. stuck
ANSWER : I had this error after the printer sat idle for many months. I thought it was the cartridge drive belt stretching, because it was extremely loose and wouldn’t move the carriage due to slippage. Then I noticed there was a gear belt tensioner to the right side that had some movement. Sure enough, when I shined a flashlight into the ink reservoir, there was a spring that had fallen down inside. Looking at the plastic belt tensioner, it looks as if the spring was held on by a plastic post that had broken off. This is most likely the cause of many of these errors, because the plastic break is very clean and not readily visible, (a design flaw in my opinion). Rather than trying to replace the part, I am going to try tapping a hole in the plastic and inserting a machine screw that can hold the tension spring in place. It also looks like the metal notch for the right hand loop of the spring, would not prevent the spring from slipping off at some point, so using a metal file to enlarge the notch may be necessary. If you’re lucky, your spring may have just popped off and is inside the ink reservoir. This may be one reason why the printer was discontinued so soon. One lousy five dollar part makes the whole printer worthless… I use this this printer primarily because it is easy to clean the heads by removing the carts, instead of having to disassemble the whole damn thing, as in ink tank designs. It makes beautiful 13×19 prints with better color accuracy than my Vivera 6 ink printer.

Read Full Q/A … :

HP Photosmart 8750

help with hp photosmart 7760
ANSWER : MIne is doing the same thing tonight!!

Read Full Q/A … :

HP Photosmart 8750

printer pulling sheets back in
ANSWER : That is strange. Only thing I can surmise is that since the A5 is a smaller size, maybe the printer thinks it is supposed to be printing on A4 and that’s why it tries to continue to print. Maybe a setting off in your software?

Read Full Q/A … :

HP Photosmart 8750

Reseting the ink levels for hp c7280,
ANSWER : I held the # and 6 down long enough to start a complete re-set of the printer But the Black ink level still shows as depleted when it is actually still half full.

Read Full Q/A … :

HP Photosmart 8750

hp 7550 printer
ANSWER : Press the Power catch () to turn on the item.

Read Full Q/A … :

HP Photosmart 8750

HP Photosmart C6180 Ink System Failure
ANSWER : This has been a life saver for us. Thank you very much for your help.

Read Full Q/A … :

HP Photosmart 8750

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :

HP Photosmart 8750

Hp 3110 ink system failure
ANSWER : Well I just solved my issue with my hp 3310 displaying the ink error code. I held the OK cancel black and color buttons down at same time. And while holding those down hit the power button when machine shut off I released buttons hit power button on it came on and shut off. Hit power button again and it will reset machine and run a maintainace program. When all is done run a print report. Mine works fine. Good luck.

Read Full Q/A … :

HP Photosmart 8750