HP LJ 5550 Magenta Problem

Press your printer`s Setup button. Go to System Setup. Choose Print Quality and then Calibrate Color. Choose Calibrate Now and press OK.

59. C0 = Developer motor rotation error. With this printer it usually means the product needs to be replaced. What you can try is to remove all toners and then start up the printer and see if the error appears.

Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.

Reasons why your HP printer has ink but won`t print

This may seem obvious, but it sometimes happens: first make sure your paper tray has paper in it. Misalignment, clogged printheads, faulty data communication or insufficient ink levels can also be sources of the problem.

If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.

Clean the printheads: Sometimes the issue why you are unable to print in color is because our printheads are clogged with ink. Clean the printheads and then print a document to check if color printing works. Some printers also have in-built programs that can clean themselves so remember to check for that.

If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.

Turn the printer off, wait 10 minutes, and then turn the printer on. 2. If the message persists, reseat the fuser. If that does not work, replace the fuser.

This error is primarily caused by a transfer alienation failure in which the ITB is stuck and unable to rotate, the SR9 sensor (the primary transfer roller disengagement sensor) has gone bad or the fuser drive assembly has failed.

Turn the printer off then back on. If the issue persists, turn the printer off, unplug the power cord and then wait at least three minutes before plugging the power cord back in and turning the printer back on. If the issue persists, ensure the product is running the latest firmware available from HP.com.

Turn the printer off. Disconnect the power cable from the printer for 30 seconds and then reconnect. Turn the printer on while you press and hold the Resume button for 10-20 seconds.

Just above the circuit board on most printer cartridges, you`ll find a small button. You`ve seen these tiny buttons before on cell phones, phone chargers, etc. This is your reset button, and the only way to get in there is either with a paper clip or the tip of a pen (which will leave a tiny ink smudge on the button).

On HP printers, a “cold reset” causes the printer to return to its factory default settings, which among other things, causes it to try and retrieve its configuration information from a BOOTP server. This is how SAP printers and Athena printers should receive their configuration information.

The default administrator or root password for all HP-provided Build Plans is: ChangeMe123! CAUTION: HP strongly recommends changing this password before deploying to any servers. See Set (encrypt) the administrator/root password for details.

There`s a chance that the printhead hasn`t been installed properly or has been clogged with dried ink or debris. If this is the case, then cleaning your printhead may resolve the HP ink system error.

There is a communication failure with the imaging drum. Turn the printer off and then on. If the error persists, replace the imaging drum. If the error still persists, contact HP. 10.000X Supply memory error or 10.100X Supply memory error.

Select Start , then select Settings > Devices > Printers & scanners . Scroll down to Related Settings and select Print server properties. Select the Drivers tab, and see if your printer is listed. If it is, you`re all set.

Your printer display or status monitor may read “Fatal Error”. This simply means a problem has occurred requiring action to clear.

The printer experienced a black drum motor M3 error. 59.05. 50 Black drum motor startup abnormality.

55 – Internal Communication Problem / Controller Error

Chances are this error has occurred due to a poor connection between the DC controller and the formatter.

If you have NOT recently replaced the fuser or moved the printer around, then the 50.2 fuser error indicates you may have an actual fuser failure and the fuser needs replacing.

The flag located right of the pick-up roller has a fixed position. If the flag becomes stuck or broken, it will produce a 60.02 tray lift error or a “LOAD PAPER” message.

1: Check Printer Power, Cables, and Paper

Check that the correct paper is properly loaded into the printer and is not jammed. Replacing damaged cables, plugging in loose or disconnected cables, and fixing paper jams as necessary may resolve the issue.

The only way to factory reset the notebook if the F11 prompt doesn`t work would be to order W8 recovery media for your specific model PC from HP. Now, if you want to clean install W8. 1, you can do that using the W8 product key in your notebook`s BIOS.