HP Color LaserJet 2500
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
A 13. B2. D2 paper jam error usually occurs when paper does not leave the paper tray.
There is a communication failure with the imaging drum. Turn the printer off and then on. If the error persists, replace the imaging drum. If the error still persists, contact HP. 10.000X Supply memory error or 10.100X Supply memory error.
The 24 character error code is a failure of the short Disk Self Test ( DST ) and would indicate that the Hard Drive is failing and needs to be replaced. Hi, It means the hard drive has failed the quick test and needs to be replaced.
An E1 or E2 error indicates that the paper size setting does not match the paper size that is loaded.
Make sure your devices are properly connected with each other, and the network or the cable you use to connect these devices is normal. You can also try restarting your HP printer. Turn it off completely and unplug the power cord, leave it for a couple of minutes, and then plug the cord back and power on the printer.
An Er/04, Er/05, or Er/06 error message indicates a paper jam. Find and clear the printer of any jammed paper, or reset the printer if the printer has no jammed paper.
The resolution for either error is to, if preferred to send a firmware update, then replace the flatbed scanner assembly. It has been found that it is in most cases the internal lamp that has failed, but is not available through HP as a replaceable part. Example of 30.03. 23 code when copying.
When a 13. E1. D2 Error appears on the control panel, it indicates there is jam because the paper cannot exit the printer. This might be caused by damage to the output bushing.
a misprint or misspelling in a text.
The “Wrong Cartridge Type/Installed” / “Print cartridge is not compatible with this device” / “Cartridge Error” / “Print Cartridge Error” / `blinking lights” alert/error message is typically indicative of failed micro-electronics internal to the ink cartridge(s).
During a print job, the printer stops feeding pages, an E4 error displays and the Resume light blinks. This indicates that paper might be jammed inside the printer. Note: Paper jams can be real or false.
An E2 error occurs when the printer attempts to print a single-page or multi-page print job, and the paper length selected in the print settings does not match the length of the loaded paper.
E8 is a common error code for HP Laserjet printers. The error message indicates a problem with the scanner carriage of your printer. This problem can either be software based, or caused by a problem with the scanner motor. First, make sure that your HP printer software is up to date.
The system error 24:10 is a critical error in which the printer cannot be used until has been corrected. Turn the printer on in Diagnostic Mode. Turn On the printer holding down Power + Cancel + DOWN buttons until you hear one beep before releasing ALL three keys.
Cause. The error may be caused if the wrong printer is set as the default printer, the printer driver is missing, or if there are conflicts in the device manager. Please help us improve by providing feedback on your experience with the document.
Control displaying F6 E1:
There may be a problem with the Main Control Board, the User Interface (Touchpad), or the associated wiring. Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Start a time dry cycle.
An E0 error indicates an unusable cartridge. This condition occurs when at least one ink cartridge needs attention, is faulty, incorrect, missing, damaged, or incompatible.
Possible causes for this error include: Swing arms are not engaged. Lift motor or clutch failure. Dirty or defective encoder disk/sensor.
For anyone else who finds this page when tracking down this error, Error 79.8109 is simply the result of using the wrong printer driver (i.e. the HP Universal PCL6 driver, as provided under Windows 8 and 10). This driver does not work correctly with this printer. In general this error isn`t a formatter problem.
For anyone else who finds this page when tracking down this error, Error 79.8109 is simply the result of using the wrong printer driver (i.e. the HP Universal PCL6 driver, as provided under Windows 8 and 10). This driver does not work correctly with this printer. In general this error isn`t a formatter problem.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr
Read Full Q/A … :
HP Color LaserJet 2500
ERROR on HP LJ 4525
ANSWER : Print a Configuration page. That will tell you what size paper Tray 2 thinks it has in it. If it doesn’t have plain letter on the page, then it will ask to print from Tray 1.
Read Full Q/A … :
HP Color LaserJet 2500
HP 9040 MFP Error code
ANSWER : bonsoir
Read Full Q/A … :
HP Color LaserJet 2500
HP 4050 Error 13.1 & 13.20
ANSWER : I tried the fix you recommended but it still would not fix.
Read Full Q/A … :
HP Color LaserJet 2500
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
HP Color LaserJet 2500
HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:
Read Full Q/A … :
HP Color LaserJet 2500
HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply
Read Full Q/A … :
HP Color LaserJet 2500
HP Color Laserjet 500 series M551n Error 98.00.0C
ANSWER : I just ran into one of these on a 4 year old m551. Failed to complete startup at the end of disk check. Followed the above link for troubleshooting.
Read Full Q/A … :
HP Color LaserJet 2500