HP LaserJet 2200

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Insert the stack of paper into the product, and then gently push the paper guides snugly against the paper. Make sure that the paper is fully inserted into the product. Try printing again. If the issue is not resolved, try loading different brands of paper and different types of paper, one type at a time.
The paper might not be engaged with the feed rollers. The paper-width guide is pressed against the paper stack too tightly. The paper tray is not completely inserted into the product. The paper settings in the print driver do not match the paper loaded in the paper tray.
The paper tray is empty or overloaded. The paper is curled. The print side, or shiny side, of the paper is not loaded in the paper tray face up. For photo paper, always load the rougher side of the paper facing down.
Dust, paper fiber, and other debris might accumulate on the pick rollers and cause paper feed issues. To help prevent paper feed issues, clean the rollers inside the printer and in the duplexer (if equipped). If the other steps in this document fail to resolve the issue, then reset the printer.
One sensor is located in the printer carriage. A second sensor—the Auto Sense sensor—is located in the back of the printer near the paper `clean out` area. Each sensor performs a specific set of media detection functions.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
If your printer keeps jamming, you should know that the most common cause of a jam is misalignment of the paper. Paper needs to load in smoothly, completely flush with the tray. Overfilling the tray is a great way to ensure you will be spending some personal time getting to know the inside of a printer.
With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.
Capacitive sensors can detect objects that have a dielectric constant that is different from air. Hence, these sensors can detect objects made from a wide variety of materials such as plastic, paper, wood, etc.
Print mark sensors are used for sensing registration mark on packaging film. These Electronic sensors include state-of-the-art technologies for providing precision results. These Electronic sensors are used in various industrial segments. Working Principle. This is designed for sensing Registration Marks.
1: Check Printer Power, Cables, and Paper

Check that the correct paper is properly loaded into the printer and is not jammed. Replacing damaged cables, plugging in loose or disconnected cables, and fixing paper jams as necessary may resolve the issue.

Printer rollers are the tiny rubber wheels inside your printer that move sheets of paper through the printer. The roller that lifts the paper from the paper tray is called the paper uptake roller.
Use isopropyl alcohol or ethanol according to the manufacturer`s safety guidelines, as applicable. Wipe the roller with a lint-free cloth dipped in isopropyl alcohol or ethanol. After cleaning the roller, make sure that no lint or other material remains on the roller.
Reset. Resetting the printer stops printing and clears the current print job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully.
Turn the printer off. Disconnect the power cable from the printer for 30 seconds and then reconnect. Turn the printer on while you press and hold the Resume button for 10-20 seconds.
Regardless of which you choose, all of your applications will be deleted and any settings will be returned to their default. 9. If you choose “Remove everything,” you will also have to decide whether you want a completely clean drive or if you would like to keep the laptop and you aren`t planning on giving it away.
It may take you 15 minutes to reset an HP laptop. As for the Acer laptop, it requires 5 hours or 3 days to finish the reset process.
Reasons why your HP printer has ink but won`t print

This may seem obvious, but it sometimes happens: first make sure your paper tray has paper in it. Misalignment, clogged printheads, faulty data communication or insufficient ink levels can also be sources of the problem.

This is often caused by the fact the pick-up roller is worn out. The layer of rubber around this plastic part overtime gets too smooth, preventing paper from feeding properly into the printer. This fix is not really hard, will take no more than half an hour and costs around 10,- (Euro or Dollar).
This is often caused by the fact the pick-up roller is worn out. The layer of rubber around this plastic part overtime gets too smooth, preventing paper from feeding properly into the printer. This fix is not really hard, will take no more than half an hour and costs around 10,- (Euro or Dollar).

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP 2200 – Won't feed paper and squeals
ANSWER : My suggestion: laser mirror motor has dry bearing (the squeal) and the printer won’t feed paper until it gets up to speed. Someplace on fixyourownprinter is an article explaining how to get to the motor & put a drop of TriFlow Synthetic PTFE oil on it. Worked for me…

Read Full Q/A … :

HP LaserJet 2200

HP 2200 – blinking attention light and tray 2
ANSWER : Nice day. (QUALITY IS OUR CULTURE)

Read Full Q/A … :

HP LaserJet 2200

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

HP LaserJet 2200

HP 842C won't pick up paper for printin
ANSWER : I have the same problem. Multiple tries to copy item…Feedback says “out of paper” which it is not. HELP…

Read Full Q/A … :

HP LaserJet 2200

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :

HP LaserJet 2200

Printer will not pick-up paper from either tray. All error lights are on.
ANSWER : That is a hard fault. You need to access the secondary fault codes to diagnose what is causing it. Follow the instructions at this link http://www.printcopy.info/?l=en&mod=free&chap=erc&brand=HP&model=LaserJet%205P&page=4

Read Full Q/A … :

HP LaserJet 2200

HP 4250n 41.3 unexpected paper size
ANSWER : BULLSHIT

Read Full Q/A … :

HP LaserJet 2200

HP LaserJet 2200dn picking up two sheets at a time
ANSWER : The solenoid is sticking. It is really easy to find on the HP 2200, but more difficult on the HP 4100. You will need to google the instructions for the 2200. As an example, here are the directions for the HP 4100:

Read Full Q/A … :

HP LaserJet 2200