Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

There are numerous possible causes for a printer that`s randomly producing blanks. The most common ones are empty ink cartridges, improper cartridge installation, and congested nozzles. Driver and software issues can sometimes cause this problem as well.
Clean the print head, if necessary. Make sure the paper size, orientation, and layout settings in your printer software are correct. Make sure your document does not contain blank pages. If your printer software has a Preview option, you can check for blank pages before you print and remove them, if necessary.
If your printer is spitting out pages full of strange characters, symbols, or strange formatting, your inkjet printer drivers may be outdated, incompatible with your operating system or corrupt. Drivers are important to the proper function of your inkjet printer and it is best to check for updates regularly.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
Select Start , then select Settings > Devices > Printers & scanners . Scroll down to Related Settings and select Print server properties. Select the Drivers tab, and see if your printer is listed. If it is, you`re all set.
Usually a quick paper setting adjustment will clear up a ghosting issue right away. Run a cleaning – Most printers have a cleaning function built into the machine. Run this a couple of times to attempt to clear up the printing issue. Inspect the drum – Sometimes excess toner powder can stick to the drum.
Just above the circuit board on most printer cartridges, you`ll find a small button. You`ve seen these tiny buttons before on cell phones, phone chargers, etc. This is your reset button, and the only way to get in there is either with a paper clip or the tip of a pen (which will leave a tiny ink smudge on the button).
Reasons why your HP printer has ink but won`t print

This may seem obvious, but it sometimes happens: first make sure your paper tray has paper in it. Misalignment, clogged printheads, faulty data communication or insufficient ink levels can also be sources of the problem.

A standard Print Head Cleaning cycle is done by clicking `Cleaning` on the Maintenance tab, then waiting a little bit until a message comes up; confirm it and click `Print Check Pattern. ` From this you can then tell what sort of Deep Clean you need to do by which lines (black or colour) are faded.
Cleaning the print head will start the ink cartridge replacement process. If you do not intend to replace an ink cartridge, press the ink button again to return the print head to its home position. The printer starts cleaning the print head and the power light and the ink lights begin flashing.
Take a warm damp paper towel or coffee filter and blot the cartridge with the printhead facing down onto the paper towel. This will remove any dried ink on the printhead. Then, hold the cartridge with the printhead facing down against a dry paper towel for 2-3 minutes. A dry paper towel will wick the ink out.
Yes, you can.

tested the performance of Original HP ink cartridges vs. remanufactured (refilled) brands. The results: Original HP ink cartridges far surpassed ink refills in both print quality and reliability.

First, locate your print head. Next, dip a q-tip in a mixture of isopropyl alcohol and warm, not hot, water. Swab the q-tip along your print head and dislodge any dry pieces of ink that may be causing blockages. Once you`re satisfied that your print head is clean, allow it to dry overnight.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
1. On the printer display home screen, select the “set up” button (it looks like a gear). 2. Select “settings” > “device settings” > “reset settings” > “reset all” > “OK” and then “Yes.”
Ghost prints happen when the drum or fuser unit within your printer become faulty. Because a fault with this element won`t heat the particles of the toner to a high enough temperature, the marks being made on the paper are much lighter in colour and appear more faded than typical documents.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
If the DC Controller turns on the laser beam continuously, the entire surface of the Photosensitive drum is neutralized causing a completely black page.
Binocular double vision is the result of misaligned eyes. This can cause the images you see to be off, resulting in ghost images.
Adjust your refresh rate and resolution

If your refresh rate or resolution is too low or too high for your monitor, it can cause flickering or ghosting. To fix this, you need to adjust your refresh rate and resolution to match your monitor`s specifications and capabilities.

When you send a print job from your computer, the computer tells the printer where to deposit the ink or toner. If there isn`t enough ink or toner left in the cartridge, the printer will display a low or empty sign to indicate you should replace the cartridge soon.
Turn on the laptop and immediately press the F11 key repeatedly until System Recovery starts. On the Choose an option screen, click “Troubleshoot.” Click “Reset this PC.”
There isn`t much that can be done in the way of repairing a printhead, only replacing parts. By the time a printer technician assesses your printer, gets the part you need, and replaces it, you could have ordered a new printhead from allprintheads.com and replaced it yourself for much less.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP LJ 1150 Printing multiple pages on one sheet?
ANSWER : Hey friends.

Read Full Q/A … :
Unknown Printer

HP Color Laserjet blank pages – only jetdirect page
ANSWER : What about the engine test? To do that, drop down the front tray. Feel around on the left side at the top and you’ll feel a little plastic dongle. If you lift up on that it will initiate an engine test page. That will be a page containing lines of each color.

Read Full Q/A … :
Unknown Printer

HP Laserjet 4000 Printing Blank Pages
ANSWER : Would just like to say thank you to every one. I am a teacher and need my printer for a ridiculous amount of paper work that keeps me away from working with students. My printer was down for 5 school days. I finally got the new toner and it still didn’t print. After following your meticulous instructions I was able to get it working. Thank you Thank you Thank you to all people who contributed to this.

Read Full Q/A … :
Unknown Printer

Prints blank pages, won't print from computer
ANSWER : Don’t know why you replaced the fuser, but assuming you had print before, then it must have been something you did during the procedure. Only thing I can suggest is to recheck your work. Just because you reinstalled a connector doesn’t mean that it is seated firmly enough to work. Any flat ribbon connectors that you removed and reinstalled, check to see that the contacts are all flat and not peeled back.

Read Full Q/A … :
Unknown Printer

HP LaserJet 2200D won't print configuration page
ANSWER : Find someone with a HP LaserJet 4100 and you can configure the card to the IP you want:

Read Full Q/A … :
Unknown Printer

HP Officejet 860 printer printing blank pages
ANSWER : First check the exact ink levels, replace if any one are low or empty.

Read Full Q/A … :
Unknown Printer

printing blank pages
ANSWER : You can’t let an inkjet printer sit that long. Try flushing the heads. Take out all the ink tanks and to the right of the assy. you will see a plastic lever. Lift it and it will release the heads. Take it to the sink and using hot running water, flush it from top and bottom several times. Then blot it dry and reinstall.

Read Full Q/A … :
Unknown Printer

I just bought an officejet 3830 2 weeks ago. Now it won't print at all! Says inkjet jam. It's not! I've done all the fixes as per hp's website now what?
ANSWER : Take it back and exchange it under warranty.

Read Full Q/A … :
Unknown Printer