HP LaserJet P3005-Install black toner cartridge-Issue

HP LaserJet P3005

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Why does my HP printer keep saying cartridge problem? Please check and wipe the cartridge contacts. The common cause of the cartridge problem message is the gold contacts found on an electronic chip on the body of the HP cartridge being cloaked with dirt or ink or even because of physical damage.

Clean the Cartridge Contacts: one of the most common reasons you might get a cartridge problem error when your cartridges are new and full is the contacts on the cartridge might be dirty or otherwise obscured from making good contact with the electronics in the printer head carriage.

To override HP ink cartridge error, remove and reinstall the indicated cartridge 2-3 times until it firmly seats in the slot. Then turn off the printer and remove all cartridges. Gently, with a dry lint-free cloth, wipe the contacts on the cartridge and carriage to remove any dirt or residue.

If you are trying to install a black ink cartridge in a color cartridge slot, your printer will not function and you could potentially cause damage to the machine. Some photo inkjet printers require two black ink cartridges to print text and more defined shades of black in your photos.

Most commonly “Cartridge Problem” means that your HP printer simply cannot recognise the colour or black ink cartridges. Thankfully however this error message can usually be cleared with some basic troubleshooting.

There are a number of reasons why ink is not flowing through the cartridge, despite there being plenty of ink in the cartridge. The most common cause for this is infrequent usage. If your printer is not used on a regular basis, at least once a week, the cartridge can dry up and then become clogged as a result.

Press the button on the chip-reset tool for several seconds until the LED light on the device goes off. Then, unlock the reset tool from the cartridge. Use the resetter with other cartridges and install them back into the corresponding slots in your printer. Voila!

The message “Replace Toner” is intended to alert you that the toner cartridge has reached the end of its expected life. It is recommended that the toner cartridge be replaced.

If your HP printer not printing black ink correctly, here`s what you should do. Using non-genuine ink cartridges. Printheads that have become clogged. Ink cartridges that are defective or empty.

You can continue to print with one or more empty cartridges, but HP recommends replacing them as soon as possible to avoid printhead damage.

When color ink is expended and black ink still remains, you can continue printing for a short time using only black ink. However, you should replace the expended ink cartridge(s) as soon as possible.

The other smaller black contains a dye based ink which is used more for photo or image printing.By using the 2 black cartridges the printer is able to produce crisp, dark text and by switching in picture mode it can also then use the smaller dye based ink to produce the highest quality photos.

There are chips inside the original cartridges to record how many pages were printed and they cannot be reset. As a result the printer reads the chips and tells you that the cartridges are empty, even though they are not. This is why you are getting the “ink low” message even though the ink tank is at full capacity.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP Laserjet 1320tn printing grey instead of black

ANSWER : Try this test. Put a page into the manual feeder and do that same test. When the end of the page is just about to enter the printer, open the lid. Take out the toner cartridge and pull back the shutter. Look at the image and see if it is black. The explanation is that there is high voltage going to both the toner cartridge and the charge transfer roller below it. If the image on the drum is black, then the fault is at the transfer roller not getting enough high voltage. The transfer roller pulls the image off of the drum and down onto the paper. It would not be a laser scanner problem as any issue with it would not result in an overall gray image, but combination of gray and black. It will probably turn out to be a bad HV power supply, which will need replacement. I’ve never seen this particular problem on this model.

Read Full Q/A … :

HP LaserJet P3005

HP 2600n LaserJet leaking toner?

ANSWER : yes, the refill toners are about 3 times more lonely to cause quality issues.

Read Full Q/A … :

HP LaserJet P3005

HP laserjet toner wiper blade fix?

ANSWER : I’m having trouble locating wiper blades & doctor blades for sale online. Can anyone suggest sources, please? I have several HP 92298X cartridges that need them.

Read Full Q/A … :

HP LaserJet P3005

HP Laserjet 4250 – RFU LOAD ERROR

ANSWER : Italiano:

Read Full Q/A … :

HP LaserJet P3005

How to copy a card slot in HP laserjet 4250N

ANSWER : None that I know of, using a computer is likely your best option but I never attempted it.

Read Full Q/A … :

HP LaserJet P3005

evenly spaced horizontal lines on hp laserjet III printout

ANSWER : The lines would be a toner cartridge problem. Which paper tray? The MF tray or the optional paper cassette?