That’s almost always a bad DC controller. Slight possibility of it being a formatter board.
How to Identify and Fix Common printer Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
An Er/03 error message indicates the printer failed to pick a sheet of paper to print. Remove the stack of paper from the tray and check the condition of the paper. Reload the paper, and then try to print, copy or scan.
The printer is either low in toner, the density is set too low, or the Economode may be turned on. Remove the toner cartridge and shake it. This will redistribute the toner and often will temporarily solve the problem. However, this usually indicates it is time to install a new cartridge.
This error condition occurs by design when an attempt to print with a PCL5e or PCL6 printer driver occurs and is NOT a bug within the product software. Install the correct HP LaserJet Host-Based Printer Driver or the HP LaserJet printing system software for the product.
The E3 error code indicates the unit has detected there is no refrigerant. The unit will require a repair service for refrigerant to be added, please visit Request a Repair page for further assistance.
If the trigger cannot be fully inserted, the door is not properly closed and the E02 or E03 error will occur. To resolve this error, you need to ensure that the printer cable is long enough to allow the door trigger to be fully inserted.
Primary causes include grime, dust, worn rollers, or incorrect paper weight.
1: Check Printer Power, Cables, and Paper
Check that the correct paper is properly loaded into the printer and is not jammed. Replacing damaged cables, plugging in loose or disconnected cables, and fixing paper jams as necessary may resolve the issue.
Printers show up under “unspecified” when Windows cannot associate an appropriate driver. Reference this article to find drivers for your Brady printer: How to Find Windows Printer Drivers for Your Brady Printer. If you have recently installed the driver, simply rebooting your PC can resolve the unspecified status.
Press and hold (or right-click) the USB external hard drive with the issue, and select Uninstall. After the hard drive is uninstalled, unplug the USB cable. Wait for 1 minute and then reconnect the USB cable. The driver should automatically load.
Cause 3 No route to destination – This cause indicates that the called party cannot be reached because the network through which the call has been routed does not serve the destination desired.
E3 indicates a combined water outlet temperature sensor error. E4 indicates a water outlet temperature sensor error.
An E1 or E2 error indicates that the paper size setting does not match the paper size that is loaded. Remove all paper from the input tray, and then load the correct paper size. Remove any paper from the input tray. Slide the paper width guide as far as possible to the left.
If the printer displays an error message, the following information should help to diagnose the problem. The led screen on the printer will flash a letter E and will then be followed by two numbers: E02 – The printer is out of paper or will not feed. E03 – The printer lid is open, or there is a paper jam.
Solution. If the orange light is lit and the E03 support code displays on your printer, there is a paper jam. Support codes 1300, 1303, and 1304 also indicate a paper jam.
This error will occur due to the paper jam inside your printer To ﬁx the error code e03 on your printer, follow the below steps. Start by turning off your Canon Printer TS3122 printer and unplugging the power cord. Now, open the front cover of the printer. Now, slowly pull out the jammed paper inside the printer.
What maintenance does a laser printer need? To keep your printer running at maximum capacity, you need to maintain its working parts. Dust and wipe it down regularly inside and out with a no-lint towel and rubbing alcohol. Turn off your printers regularly, especially when they aren`t in use for a long while.
The Print Spooler is software built into the Windows operating system that temporarily stores print jobs in the computer`s memory until the printer is ready to print them. In some circumstances you may need to stop and/or restart the service.
Your printer display or status monitor may read “Fatal Error”. This simply means a problem has occurred requiring action to clear.
Click Start on your computer, then select Devices and Printers. Right-click on the printer`s icon that did not install correctly, then select Troubleshoot. After you confirm that the printer driver for the device you want to use is not installed, select Apply this fix.
To choose a default printer: Select Start > Settings . Go to Devices > Printers & scanners > select a printer > Manage. Then select Set as default.
To fix the error code 0x0000011b related to networked or shared printers, Microsoft says you should disable the print spooler privacy settings on both the Client PC (from which you work) and Print Server (Workstation to which the printer is attached).
RESET THE PRINTER
Switch the printer on and unplug the cable completely, both the USB connection on the device and the plug to the power socket. Wait for at least a minute. c. Reconnect the cable and plug it to the power source.
Check the USB cable for damage and recommended length, and then restart your printer and computer. Turn off the printer and the computer. Disconnect the USB cable from the computer and printer, and then inspect the cable. If the cable is damaged or longer than 3 m (9 ft 10 in), replace it.
Press f11 while the computer is starting. Or, press and hold f11 as you press the power button.