HP Laserjet IIIP problem

HP LaserJet IIIP+

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

An Er/03 error message indicates the printer failed to pick a sheet of paper to print. Remove the stack of paper from the tray and check the condition of the paper. Reload the paper, and then try to print, copy or scan.

The printer is either low in toner, the density is set too low, or the Economode may be turned on. Remove the toner cartridge and shake it. This will redistribute the toner and often will temporarily solve the problem. However, this usually indicates it is time to install a new cartridge.

Er/11, Er/14, or Er/17: The toner cartridge is not compatible with the printer, has been protected on another printer, or is an unauthorized toner cartridge.

If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.

Error Code 3 is a Windows error code that appears when the computer cannot find the specified path.

The error code 004-311 indicates an issue with the optional duplex module. Switch the printer off, reseat the duplexer then switch the printer back on.

Turn off the HP printer and unplug it from the power source. Also, shut down your computer and unplug any external devices. Wait for a few minutes and then plug in the printer and turn it back on. Finally, turn on your computer and check if the error state has been resolved.

Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.

41.2 Error Code on HP Laser Printers

The 41.2 is still is a laser/scanner error—the good old “temporary loss of beam detect.” And in most printers, the possible causes are the same as always: bad laser/scanner (by far the most common), bad DC controller board, or bad connections between these two.

Most printers will stop working when they`re out of paper, ink or toner, or if the unit detects an issue with the ink or toner cartridge. When this occurs, you might receive an error message or notice blinking green or amber lights on your printer.

1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.

A mistake in anything that`s printed is a misprint. You might also call it a typographical error or typo.

Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.

An error 03 on the E3Point is a sensor board eeprom error. Which can be caused by corrupt data or due to the E3Point not reading the sensor correctly. To resolve it, follow: Power down the E3Point and remove the sensor cartridge.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

What repair needs to be done for a "50 needs repair" message on an HP Laserjet IIIP?

ANSWER : I don’t know what you mean by good toner cartridges. They haven’t been built in about 10 years, so if they are new OEMs in the box, they are guaranteed to fail. The 50 error on that printer is mostly a burned out fuser lamp. This site was sold, so as you can see, there are no more kits available.

Read Full Q/A … :

HP LaserJet IIIP+

evenly spaced horizontal lines on hp laserjet III printout

ANSWER : The lines would be a toner cartridge problem. Which paper tray? The MF tray or the optional paper cassette?

Read Full Q/A … :

HP LaserJet IIIP+

HP Laserjet 2200, Tray 2 Pickup Problem, Gears Clicking

ANSWER : Definitely not a solenoid problem. I’ve worked on tens of thousands of printers and never replaced a single solenoid. You probably knocked something loose when you installed the pickup roller. Maybe something to do with the gear on the end of the pickup roller shaft. You’ll need to take the gear assembly off to be able to see it.

Read Full Q/A … :

HP LaserJet IIIP+

HP Color Laserjet 3800 problem when printing color

ANSWER : Do a cold reset

Read Full Q/A … :

HP LaserJet IIIP+

HP Laserjet M3035xs RFU Upgrade

ANSWER : There’s no way.

Read Full Q/A … :

HP LaserJet IIIP+

How to copy a card slot in HP laserjet 4250N

ANSWER : None that I know of, using a computer is likely your best option but I never attempted it.