HP LaserJet 6L

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary. Then reload the paper. If thick media does not feed, make sure you are loading it straight into the product, not at an angle. If paper jams when you print on both sides of the paper, try loading fewer sheets.
The common reasons for this issue are various, for instance, the paper input tray is overloaded, dust or moisture can affect the paper feed or paper pick rollers, the printer driver is old, etc. Thus, the printer cannot detect the paper that has been inserted into the tray.
The paper tray is empty or overloaded. The paper is curled. The print side, or shiny side, of the paper is not loaded in the paper tray face up. For photo paper, always load the rougher side of the paper facing down.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust.
Dust, paper fiber, and other debris might accumulate on the pick rollers and cause paper feed issues. To help prevent paper feed issues, clean the rollers inside the printer and in the duplexer (if equipped). If the other steps in this document fail to resolve the issue, then reset the printer.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
The most common cause of this issue is paper misalignment. Make sure you properly insert the papers in the tray and avoid overfilling the tray. If this doesn`t solve the problem, check the troubleshooting section of the printer`s user manual.
Using both hands, put one piece of paper in the manual feed slot until the front edge of the paper touches the paper feed roller. Once the machine has grasped the paper, let go. The side to be printed should be faced up. The machine will hold the paper in place until the print data is sent to the machine.
The paper might not be engaged with the feed rollers. The paper-width guide is pressed against the paper stack too tightly. The paper tray is not completely inserted into the product. The paper settings in the print driver do not match the paper loaded in the paper tray.
When the printer tells you to load tray 1 it means the size and or type of paper being asked by the print job does not match the same that the printer thinks it has in the tray.
Printer rollers are the small circular rubber pieces that help feed printer paper through your printer. Over time, they can accumulate dust from the paper and ink residue from printing double-sided pages. To clean your printer rollers, you`ll need to first locate them in your printer.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

HP LaserJet 6L

HP LaserJet 1200 Early Feeding Causes Paper Jam
ANSWER : Seriously, dmzcompute, you are awesome! And this is just what the internet does so well: a specific fix for an esoteric problem, thus keeping a 15 year old machine alive another day. Thank you!

Read Full Q/A … :

HP LaserJet 6L

HP Laserjet 6MP wont feed paper
ANSWER : I had a similar paper pickup problem on laserjet 6mp. The printer would go through start-up sequence fine but when it received a print job you could here the main gears/rollers turning but no clicking from paper pickup solenoid, then eventually error lights would come one . I incorrectly assumed it was an error with the paper pickup mechanism and wasted a whole day taking the printer apart and replacing the paper pick mechanism. Long story short, if I had bothered to figure out the secondary error light codes from the start, I would have realized it was just a bad fuser and would not have wasted so much time.

Read Full Q/A … :

HP LaserJet 6L

HP 1220C Photo Paper Feed Problems
ANSWER : This problem isn’t about the paper picker. Here is the real issue and fix:

Read Full Q/A … :

HP LaserJet 6L

HP laserjet 3100 multiple page feed fixed!
ANSWER : Can you tell me what kit you are referring to because I have the exact problem with my 3100 printer?

Read Full Q/A … :

HP LaserJet 6L

HP Laserjet 2200, Tray 2 Pickup Problem, Gears Clicking
ANSWER : Definitely not a solenoid problem. I’ve worked on tens of thousands of printers and never replaced a single solenoid. You probably knocked something loose when you installed the pickup roller. Maybe something to do with the gear on the end of the pickup roller shaft. You’ll need to take the gear assembly off to be able to see it.

Read Full Q/A … :

HP LaserJet 6L

Paper Feed Problem on HP R80
ANSWER : In the last examination it is our origination of death which chooses our responses to all the inquiries life puts to us. The most pleasant spot to be is in somebody’s idea; the most secure spot to be is in somebody’s petitions.

Read Full Q/A … :

HP LaserJet 6L

HP DeskJet 722C Paper Feed Problem
ANSWER : Detach the force string from the holding nothing back one and expel all paper from it.

Read Full Q/A … :

HP LaserJet 6L