HP LaserJet 4250

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.
13 – Paper Jam

If this code appears you have a paper jam, newer models of HP printers will tell you where the jam is located so you can just follow the instructions on the screen to resolve the error code.

The 13.02 error message indicates that paper did not clear the top of page sensor (PS103) within the specified amount of time allotted by the DC Controller. This sensor is located underneath the registration assembly. The jam message may vary depending on the location of the page or pages that may be jammed.
According to technical documentation this error is usually caused when trying to print on a unit that had either an internal or external finisher and that device has been removed, without replacing the flag assembly that is used for standard output bin.
If a cable is inserted into the plug, it may cause the communication error, disconnect it. If there is still no communication between the scanner and scale return the unit to an authorized service center for repair.
This error can mean that an electrical component is disconnected or is having difficulty communicating with the other components. If you`re getting this error, power cycle your printer by turning it off for one minute and then restarting it.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
When a 13. E1. D2 Error appears on the control panel, it indicates there is jam because the paper cannot exit the printer. This might be caused by damage to the output bushing.
A 13. FF. FF error is related to jams in the paper path. These errors indicate that the product powered up with a jam.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
An Er/01 error message indicates the input tray is empty. To resolve the error, make sure paper is correctly loaded in the input tray. Lift the dust cover. Slide the paper width and paper length guides to their outermost positions.
The error 33.02. 01 means there is a used board /disk installed. That means an encrypted board or disk with existing data previously locked to a different printer has replaced the original.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:

Read Full Q/A … :

HP LaserJet 4250

HP 4250, error 54.1 Remove sealing tape from toner
ANSWER : I am having the same problem as everyone else can someone send me a new link or the pdf

Read Full Q/A … :

HP LaserJet 4250

HP LaserJet 49 Error Troubleshooting
ANSWER : One must give a chance to 25dollarsupport its a Fix $ price Computer Tech support company, which is the best option in present crowded market. Quite dependable and cost effective..

Read Full Q/A … :

HP LaserJet 4250

Service manual for an HP Laserjet 4250 (or 4250n)
ANSWER : Hello all,Can someone please tell me where to find service manual for a 4250 or 4250n printer?I used Google, Fileshare.eshop.bg, peer-to-peer, but with no avail …Thanks alot for your answers!

Read Full Q/A … :

HP LaserJet 4250

HP Laserjet M3035xs error 13.17.00
ANSWER : If the misstep thinks of no interface join connected with the unit, pay for my research paper then most times the issue is the hard circle and it ought to be supplanted.

Read Full Q/A … :

HP LaserJet 4250

Laserjet 4250 print quality issue (see image)
ANSWER : It looks like a fuser problem. One way to prove it is with the half-stop test. Put a sheet in the drop down manual feed tray. Send a print job and watch the paper. When the end of it is about to enter the printer, open the lid and take out the toner cartridge. Look at the printed image. If it looks OK, then it is a fuser problem. If not, then it is a toner cartridge issue since it hasn’t gone through the fuser.

Read Full Q/A … :

HP LaserJet 4250

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :

HP LaserJet 4250

HP 4250 13.06.00 Fuser output paper stop !
ANSWER : pick up solenoid

Read Full Q/A … :

HP LaserJet 4250