HP DesignJet 70

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

HP LaserJet Pro M304, M305, M404, M405 – 13.08, 13.09 jam error in the toner cartridge or fuser area
  1. Press the front door release button. …
  2. Open the front door on the printer. …
  3. Remove the toner cartridge from the printer. …
  4. Lift the jam-access cover. …
  5. If jammed paper is visible, remove any jammed paper.
Paper Is Jammed inside Printer
  1. Turn off printer and unplug it.
  2. Open scanning unit / cover. Important. …
  3. Check if jammed paper is under print head holder. …
  4. Hold jammed paper firmly in both hands. …
  5. Slowly pull out paper, so as not to tear it. …
  6. Make sure all jammed paper is removed. …
  7. Close scanning unit / cover.
To Clear the Paper Jam From the Fuser Area:
  1. Lift the rear door release and pull open the door.
  2. To open the paper guide on the top of the fuser, lift the paper guide tab.
  3. Remove any jammed paper from the back of the printer.
  4. Close the paper guide on the fuser.
  5. Close the rear door.
2 avr. 2018
Input trays
  1. Pull any visible jammed media out of the priority input tray.
  2. Open tray 1 and pull any visible jammed media out of the device.
  3. If no media is visible, open the print-cartridge door, remove the print cartridge, and then carefully pull the media up and out of the device.
Input trays
  1. Pull any visible jammed media out of the priority input tray.
  2. Open tray 1 and pull any visible jammed media out of the device.
  3. If no media is visible, open the print-cartridge door, remove the print cartridge, and then carefully pull the media up and out of the device.
Clear jams in the paper input tray
  1. Pull out the tray, and lift the jam access door above the tray. Figure : Pull out the tray.
  2. With both hands, grasp the paper, and carefully pull it free from the product. Figure : Remove jammed paper.
  3. Replace the tray. Figure : Replace the tray.
  4. Press the OK button to continue printing.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP LaserJet 1200 Early Feeding Causes Paper Jam
ANSWER : Seriously, dmzcompute, you are awesome! And this is just what the internet does so well: a specific fix for an esoteric problem, thus keeping a 15 year old machine alive another day. Thank you!

Read Full Q/A … :

HP DesignJet 70

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :

HP DesignJet 70

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

HP DesignJet 70

HP Laserjet 6MP wont feed paper
ANSWER : I had a similar paper pickup problem on laserjet 6mp. The printer would go through start-up sequence fine but when it received a print job you could here the main gears/rollers turning but no clicking from paper pickup solenoid, then eventually error lights would come one . I incorrectly assumed it was an error with the paper pickup mechanism and wasted a whole day taking the printer apart and replacing the paper pick mechanism. Long story short, if I had bothered to figure out the secondary error light codes from the start, I would have realized it was just a bad fuser and would not have wasted so much time.

Read Full Q/A … :

HP DesignJet 70

Paper Mismatch Error on HP C6150, C6180 or C7280
ANSWER : Thanks a lot for your informational post. I had been working online and making money through paypal generator if you also want to know the secrets behind what you can do with this free paypal money adder visit the website and take away cash in your account.

Read Full Q/A … :

HP DesignJet 70

LaserJet 4 won't Power Up
ANSWER : I haven’t seen that particular behavior on that model. It either works or it doesn’t. My first choice would be the power supply.

Read Full Q/A … :

HP DesignJet 70

Paper Jam 13
ANSWER : Sticky paper pickup solenoid. Since MF tray doesn’t use it, it works fine. Solenoid is located on right side of printer at the end of the paper pickup roller shaft. You need to remove the solenoid, take the plate and spring off the top and then scrape off the gooey residue that’s causing it to stick. Then you get a thin piece of sticky backed felt and put it on top of the metal base. You can find some at the local hardware store, they’re used on the bottom of chair legs.

Read Full Q/A … :

HP DesignJet 70

HP LaserJet 4200 paper jam fix
ANSWER : Yes, thank you! You did a thorough post! If your still hacking away at HP’printers you will know that unfortunately HP kept using that type of solenoid with the “Sticky Mess” on all of their new Equipment. I use this method almost everyday (without removing the actual solenoid). I’ve replaced so many I got carried away and now, I sell a solenoid repair kit! It’s for those people that like convenience. I provide a professional supply of perfect material with sticky back tape pre-cut to exact dimensions! All in a little kit. I have install videos, (I don’t charge for that I believe in the Do-it -Yourself approach.) Sorry for the sales pitch… but here is my link.

Read Full Q/A … :

HP DesignJet 70