HP OfficeJet LX
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
To brief on teh functionality- Fuser assembly is made up of heating element, thermistors, teflon etc. if thermistor is not able to reach to the operataing temperature so that it can send signal to the printer that i am ready to work, then it gives 50.0 error message.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
A high fuser temperature error has occurred. Note: A fuser error might occur because of inadequate power supply, inadequate line voltage, or a fuser problem.
I found the following: Error 50 means that the heating of the fuser unit is no longer working. This is usually a burnt-out heating lamp,or a defective thermal fuse.
Machine Error 50 is an indication of a mechanical malfunction of the Brother machine. Unplugging the machine from the power outlet for approximately 30 seconds and then plugging it back in may temporarily resolve the issue.
Click on your Apple menu and go to System Preferences. Then select Energy Saver and uncheck the option that says Put the hard disks to sleep when possible. Save the settings and check if error 50 is gone.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
50.2 error indicates that the printer is not heating up fast enough. This can be caused by a bad heating element in the fuser but can also be caused when the printer does not have adequate power due to overloaded circuits or being plugged into a power strip or surge bar that limits current flow.
The P4014 series use a thin fuser sleeve as a medium to heat the paper. Error 50.8 suggests one end of the fuser is not heating up which may be damage to the sleeve or heavy media.
If you are experiencing a “50.7” fuser error, first turn the printer off and back on. Sometimes the error will temporarily go away with a reboot so you can print a few more pages, but usually the error reappears.
The SMS error code for an invalid destination number is “50.” The network carrier sends out this SMS error code when the destination number entered is not correct, not SMS-enabled or is a landline number. A sender will receive this notification when the message was sent to a wrong phone number or invalid destination.
The message “Unable to Print 50” will appear on the display for one of the following reasons: i. A foreign object, such as a paper clip or ripped piece of paper, is stuck in the machine; ii.
This issue comes if the user specified in the LDAP connector is not having sufficient privileges to write to the particular object. 1) For Solution, enter CR with a Workaround if a direct Solution is not available. 2) For HOW TO, enter the procedure in steps. 3) For FAQ, keep your answer crisp with examples.
Code 50 = Memory initialization error.
Turn the printer off. Disconnect the power cable from the printer for 30 seconds and then reconnect. Turn the printer on while you press and hold the Resume button for 10-20 seconds.
1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.
a misprint or misspelling in a text.
Volatile memory requires power to store the information. Deleting volatile memory is easy: Simply shut down or unplug your printer for a minute or so. Most printers also have non-volatile memory (a hard drive) that is stored until you physically delete it.
When a 50.4F. 00 error is displayed on the control panel, it indicates that there is an issue with the fuser or the power outlet where the printer is connected. Turn the printer off, and then back on to clear the error. Ensure that the power outlet, to which the printer is connected, is in good working condition.
Error 50.2 suggests the fuser can`t heat up properly. This might be fuser failure but could also be a power supply issue. Plug the printer directly into a wall socket, not into an extension. Try turning off, wait 20 minutes then on again.
Error 50 is Invalid destination number. Are you trying to send a shortcode?
unable to send sms error code 50 happens when the sms service has been blocked for 24hrs as per government rule. usually this happens after sim card replacement in any operator.
An event ID 50 message is logged if a generic error occurs when Windows is trying to write information to the disk. This error occurs when Windows is trying to commit data from the file system Cache Manager (not hardware level cache) to the physical disk. This behavior is part of the memory management of Windows.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
What repair needs to be done for a "50 needs repair" message on an HP Laserjet IIIP?
ANSWER : I don’t know what you mean by good toner cartridges. They haven’t been built in about 10 years, so if they are new OEMs in the box, they are guaranteed to fail. The 50 error on that printer is mostly a burned out fuser lamp. This site was sold, so as you can see, there are no more kits available.
Read Full Q/A … :
HP OfficeJet LX
HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr
Read Full Q/A … :
HP OfficeJet LX
HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:
Read Full Q/A … :
HP OfficeJet LX
HP 4050 Error 13.1 & 13.20
ANSWER : I tried the fix you recommended but it still would not fix.
Read Full Q/A … :
HP OfficeJet LX
HP 9040 MFP Error code
ANSWER : bonsoir
Read Full Q/A … :
HP OfficeJet LX
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
HP OfficeJet LX
HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply
Read Full Q/A … :
HP OfficeJet LX
error 50
ANSWER : Most likely the quartz lamp in the fuser assy. burned out. you can remove it and check the resistance on the 2 large pins in the connector. Should be several ohms.
Read Full Q/A … :
HP OfficeJet LX