How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Meaning: the paper exit tray is closed / Paper jam. Solution: the paper is jammed. Remove the jammed paper, replace the paper correctly in the printer, and then press the Resume / Cancel button. Meaning: the tank cartridge is not correctly installed or has run out.
The orange blinking light on the ink cartridges could be related to the cartridge error. 1) Take out the cartridges. 2) Unplug the power cord from the printer & wall. 3) Wait for 30 seconds.
Ink has run out. (The lamp on the ink tank flashes.) If printing is in progress, stop printing, replace the ink tank, and then print again. Printing under the current condition may damage the printer.
The Power light blinks at a steady interval when the printer is processing a print job. If the Power light blinks fast, the ink cartridge door might be open, or the printer might be in an error state.
Troubleshoot a blinking orange light on HP DeskJet.
It indicates firmware issues, paper jams, or improperly installed cartridges. Resolve it by performing a power reset of your printer. Take out the installed cartridges. Disconnect the device by removing the power cord from the outlet and the rear end.
Check the output of the AC adapter. If it is bad then it appears the battery has fully discharged and you need a new AC adapter.
The orange light means that your mouse pad has been disabled and you won`t be able to use it. Double tap on the upper left side of your keypad to activate it again and the light should turn off.
Printer detected ink out condition (The lamp on the ink tank flashes). Stop printing, replace the ink tank, and then print again. Be sure to replace the empty ink tank before resuming printing.
Ink in a cartridge is low. You can continue printing, or check which cartridge is low and replace it. An ink cartridge is expended or not installed correctly. Replace or reinstall the cartridge.
The power light is on or flashing. The ink light is flashing. Ink in a cartridge is low. You can continue printing, or check which cartridge is low and replace it.
Just above the circuit board on most printer cartridges, you`ll find a small button. You`ve seen these tiny buttons before on cell phones, phone chargers, etc. This is your reset button, and the only way to get in there is either with a paper clip or the tip of a pen (which will leave a tiny ink smudge on the button).
White: The battery charge is greater than 90 percent. Amber: The battery charge is from 0 to 90 percent. Off: The battery is not charging.
Start by plugging in your computer to see if the LED light shows power going to the laptop. If it lights up, your device is receiving power, which means your problem isn`t the cord or power source. If the light doesn`t come on, check your cord. Many come in two pieces, so ensure that they are connected tightly.
Check your graphics driver
Your graphics card driver might be directly related to the orange screen issue. Maybe the GPU card is not properly connected to the computer unit. Otherwise, it might have an incompatible or obsolete driver.
Regardless of what symptoms you`re noticing, the battery light is telling you a simple truth: you have battery problems, and your car isn`t getting enough current from the battery to operate correctly. That means it`s time to take action, starting with some simple maintenance.
Fast flashing indicates a poor connection between the battery and charger or a problem with the battery pack. Refer to the rechargeable battery does not charge properly using the supplied battery charger article for details. Afterwards, try charging the battery again.
With the printer turned on, disconnect the power cord from the printer. Unplug the power cord from the power source. Wait 60 seconds. Reconnect the power cord to a wall outlet and to the printer.
The ink charge is the recommended way of getting ink into the printer for the first time or for flushing the ink out of the printer with cleaning solution. It is also used when the head clean function is unable to clear clogged nozzles.
Press the button on the chip-reset tool for several seconds until the LED light on the device goes off. Then, unlock the reset tool from the cartridge. Use the resetter with other cartridges and install them back into the corresponding slots in your printer. Voila!
Turn the printer off. Disconnect the power cable from the printer for 30 seconds and then reconnect. Turn the printer on while you press and hold the Resume button for 10-20 seconds.
Turn on the laptop and immediately press the F11 key repeatedly until System Recovery starts. On the Choose an option screen, click “Troubleshoot.” Click “Reset this PC.”
Supposedly, a flashing orange light (after putting a battery in the charger) means that the batter is dead (been charged too many times) or is damaged.