HP DesignJet 130

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The common reasons for this issue are various, for instance, the paper input tray is overloaded, dust or moisture can affect the paper feed or paper pick rollers, the printer driver is old, etc. Thus, the printer cannot detect the paper that has been inserted into the tray.
To be specific, you should make sure that your printer has sufficient paper, ink or toner and without paper jam. If the printer cartridge`s status is faulty, you should replace it with a new one. After carrying out these operations, check if the HP printer can print properly. If not, try other methods immediately.
Make sure that the Service Station path is clear. Remove any visible obstacles (screws, plastic parts, etc.) restricting the movement of the Service Station. If the carriage has stopped over the service station, on the right side of the product, check that the cutter is not activated.
A piece of paper stuck in the paper tray or inside the printer can create a paper jam. Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.
When a 31.13. 13 error appears on the control panel, it indicates that there is a jam in the document feeder because the feeder cover is open. Open then close the document feeder cover. If issue remains, open the document feeder cover.
According to technical documentation this error is usually caused when trying to print on a unit that had either an internal or external finisher and that device has been removed, without replacing the flag assembly that is used for standard output bin.
A good way to stop the printer becoming jammed, is to fan the paper before you put it in the tray as this will shake out any dust and reduce static, which are two major causes of paper jams. Another way to avoid a printer paper jam is to keep your machine clean.
Capacitive sensors can detect objects that have a dielectric constant that is different from air. Hence, these sensors can detect objects made from a wide variety of materials such as plastic, paper, wood, etc.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

HP DesignJet 130

HP 26 vs HP 29 cartridge compatibility
ANSWER : Eu decidi fazer um binário opções, o primeiro passo neste trabalho yavlyaetsya formação inicial e os fundamentos .. Put Options and Call Options Trading É por isso que eu escolhi um par de artigos de alguns sites na Internet, se você pode se perguntar vospolzovatsya put-call-options.com/br/what-are-options/binary-options-and-strategies

Read Full Q/A … :

HP DesignJet 130

HP Designjet 750C+
ANSWER : I was replacing the belt on my 750c and let the y-axis motor slip out of my hand. This caused the two wire terminals to disconnect from the motor. Does anyone know which terminals the white and black wires attach to? One of the terminals has a red dot beside it and I assume this is an indicator, but do not know which wire connects there. Any help would be greatly appreciated.

Read Full Q/A … :

HP DesignJet 130

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :

HP DesignJet 130

HP LaserJet 4200 paper jam fix
ANSWER : Yes, thank you! You did a thorough post! If your still hacking away at HP’printers you will know that unfortunately HP kept using that type of solenoid with the “Sticky Mess” on all of their new Equipment. I use this method almost everyday (without removing the actual solenoid). I’ve replaced so many I got carried away and now, I sell a solenoid repair kit! It’s for those people that like convenience. I provide a professional supply of perfect material with sticky back tape pre-cut to exact dimensions! All in a little kit. I have install videos, (I don’t charge for that I believe in the Do-it -Yourself approach.) Sorry for the sales pitch… but here is my link.

Read Full Q/A … :

HP DesignJet 130

HP LaserJet 1160 pick-up problem
ANSWER : Take the black rubber roller out. Clean it and turn it 90-180 degrees so there is fresh rubber in the “corner”.

Read Full Q/A … :

HP DesignJet 130

HP 4250n 41.3 unexpected paper size
ANSWER : BULLSHIT

Read Full Q/A … :

HP DesignJet 130

HP DeskJet 510 – problem
ANSWER : Recently started to look for a trusted and high-quality work with a broker for binary options, but the search was not a very successful, and my friend who is already a few years makes this kind of activity offered me options brokers review – site who himself uses optionsbrokersreview.com

Read Full Q/A … :

HP DesignJet 130