HP DesignJet 130

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

System Error 03:10 – Technical Support

Normally this error code can only be resolved by replacing the Power Supply Unit. Often the error occurs at the same time as a loud mechanical noise coming from the power supply unit. This means the bearings in the cooling fan have failed and the power supply has in-turn failed.

Assuming these errrs are the same for all/most other Designjet printers then the 0X00010 is an overheat within the printhead.
A Go/03 error message indicates the print job is different from the current print settings. To resolve the issue, load the correct size paper in the input tray, or change the print settings to match the print job.
Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.
10.23.15 Install Fuser kit

The fuser is either not installed, or not correctly installed in the printer.

If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed. SUBSCRIBE RSS FEEDS.
An ink system failure error, the `0xc19a0013` error code appears in the printer Control panel. The error can occur due to many reasons, the most common ones being the following: The printer cartridges are not installed correctly. The printer cartridge is low.
Toner cartridge sensor error.
Error Code 3 is a Windows error code that appears when the computer cannot find the specified path.
This error code means that there`s a problem with your connection while using the Epic Games Launcher. Try following the steps in this article to troubleshoot the issue.
The E3 error code indicates the unit has detected there is no refrigerant. The unit will require a repair service for refrigerant to be added, please visit Request a Repair page for further assistance.
When a 30.03. 23 Error Alignment Calibration Failure appears on the control panel, it indicates there is an issue calibrating the scanner. If there is also a copy or scan quality issue you will see a stripe of lines from the leading edge to the trailing edge of each page.
When a 31.13. 13 error appears on the control panel, it indicates that there is a jam in the document feeder because the feeder cover is open. Open then close the document feeder cover. If issue remains, open the document feeder cover.
An Er/01 error message indicates the input tray is empty. To resolve the error, make sure paper is correctly loaded in the input tray. Lift the dust cover. Slide the paper width and paper length guides to their outermost positions.
When a 13. E1. D2 Error appears on the control panel, it indicates there is jam because the paper cannot exit the printer. This might be caused by damage to the output bushing.
When a 30.03.22 error is displayed on the control panel, it indicates that there is an error calibrating the scanner. Turn the printer off, and then back on to clear the error. If the issue continues, contact HP technical support to perform more complex troubleshooting steps.
23 or 30.03. 45 Scanner Errors. The resolution for either error is to, if preferred to send a firmware update, then replace the flatbed scanner assembly. It has been found that it is in most cases the internal lamp that has failed, but is not available through HP as a replaceable part.
The error may occur when there is a communication issue between the formatter and the scanner. Turn the printer off and then back on to clear the error message. note: Performing this action will remove all custom configurations, settings, and files.
1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.
Some of the most common printer problems that most of us have experienced include paper jamming, slow printing, uneven printing, and wrong colour output. If you use your printer frequently, we know how annoying it can be to have persisting problems with the printer.
There is a communication failure with the imaging drum. Turn the printer off and then on. If the error persists, replace the imaging drum. If the error still persists, contact HP. 10.000X Supply memory error or 10.100X Supply memory error.
Go to Solution. This error indicates a RAM failure. The specific memory is internal memory not one of the dimm slots. You can try removing any additional memory first to see if the device will boot but likely this is a failure of the formatter and you would need to replace the formatter.
That error code indicates a failure of the yellow laser scanner. Unplug and leave for a few minutes, also make sure you are plugged directly into the wall and not into a surge protector.
HELP 16.83:11 – POST CURING BURST RESISTOR NOT CONNECTED

It`s a hardware error, there`s either an issue with the air curtain resistor or with the cable. If it happens consistently, you should contact your support representative.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP 510 severe error 0x8010003
ANSWER : Eu decidi fazer um binario opcoes, o primeiro passo neste trabalho yavlyaetsya formacao inicial elizabeth os fundamentos .. put-call-options.com/br/ Collection Alternatives and Contact Opportunities Trading E por isso que eu escolhi um level delaware artigos delaware alguns websites na Web, se voce pode se perguntar vospolzovatsya

Read Full Q/A … :

HP DesignJet 130

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :

HP DesignJet 130

HP Designjet 750C+
ANSWER : I was replacing the belt on my 750c and let the y-axis motor slip out of my hand. This caused the two wire terminals to disconnect from the motor. Does anyone know which terminals the white and black wires attach to? One of the terminals has a red dot beside it and I assume this is an indicator, but do not know which wire connects there. Any help would be greatly appreciated.

Read Full Q/A … :

HP DesignJet 130

Hp designjet 500 error code 11:11
ANSWER : I have an HP designjet 510 I just powered it on and it only shows error 11:11. does anybody have a solution?

Read Full Q/A … :

HP DesignJet 130

HP 26 vs HP 29 cartridge compatibility
ANSWER : Eu decidi fazer um binário opções, o primeiro passo neste trabalho yavlyaetsya formação inicial e os fundamentos .. Put Options and Call Options Trading É por isso que eu escolhi um par de artigos de alguns sites na Internet, se você pode se perguntar vospolzovatsya put-call-options.com/br/what-are-options/binary-options-and-strategies

Read Full Q/A … :

HP DesignJet 130

HP LaserJet 1160 pick-up problem
ANSWER : Take the black rubber roller out. Clean it and turn it 90-180 degrees so there is fresh rubber in the “corner”.

Read Full Q/A … :

HP DesignJet 130

HP C6180 Hard Reset procedure
ANSWER : How do I hold down the # and the 6 at the same time? The “#” requires holding the shift key and the “6” doesn’t. Maybe you all have a different type of keyboard. My printer is HP 1220C.

Read Full Q/A … :

HP DesignJet 130

HP DeskJet 510 – problem
ANSWER : Recently started to look for a trusted and high-quality work with a broker for binary options, but the search was not a very successful, and my friend who is already a few years makes this kind of activity offered me options brokers review – site who himself uses optionsbrokersreview.com

Read Full Q/A … :

HP DesignJet 130