HP Colour laserjet 2550n printer Tray2 issues

HP Color LaserJet 2550N

Experienced technical support provide their insights in answering this question :

Ensure that the printer is turned on and in the Ready state.

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If you see the error message “50.2 Fuser Error” on your HP Color LaserJet CP2025 series printer, you probably need to replace the fuser. Fusers are a consumable part and it is expected over the life of the printer you will replace the fuser several times.

When a 50.4F. 00 error is displayed on the control panel, it indicates that there is an issue with the fuser or the power outlet where the printer is connected. Turn the printer off, and then back on to clear the error. Ensure that the power outlet, to which the printer is connected, is in good working condition.

This error might display if the fuser temperature becomes too hot. Follow these steps to turn off the printer and allow the fuser to cool before printing again. Press the Power button to turn off the printer. Disconnect the power cord from the rear of the printer.

The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.

The fuser unit or fuser is a critical part of any laser printer. Using pressure and heat, it fuses the toner powder onto the page to create a print, and without it, the printer cannot operate.

Streaking, smudging, black lines, and double images are all symptoms of a bad fuser. When you notice these printing defects and experience problems, such as paper jams or wrinkles, this is a good sign to replace the fuser kit.

Among the more common technical issues that may bring down a printer are disconnected cables, malfunctioning routers, and low ink levels. Moreover, software problems such as interrupted connections or incorrect settings in your system`s drivers can also cause your printer to show up as offline.

Any of these error codes (51.20 51.21 51.22 51.23) points to a failure with one of the laser scanner assemblies on the HP Color LaserJet 4610 an 4650 series. To solve these error codes, replace the corresponding laser scanner.

Your printer monitors the life of your fuser. When the fuser reaches the end of its life, the printer displays 80 Fuser Exhausted. This message indicates it is time for you to replace the fuser. For best print quality, make sure you replace the fuser when the printer displays 80 Fuser Life Warning.

The message “Replace Fuser” will appear on the display when the machine has printed approximately 100,000 pages (at 5% coverage on letter/A4 paper). The fuser unit is a periodic maintenance part and should be replaced to maintain optimum print quality and reliability and to prevent paper jams.

F0 Error and is unable to print. This error is primarily caused by one of the following conditions: A transfer alienation failure in which the ITB is stuck and unable to properly engage the internal transfer rollers. The SR9 sensor (the primary transfer roller disengagement sensor) has gone bad.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP Colour laserjet 2550n printer Tray2 issues

ANSWER : Ensure that the printer is turned on and in the Ready state.

Read Full Q/A … :

HP Color LaserJet 2550N

My 2550n Color LaserJet does not want to print in color

ANSWER : That model had issues with the carousel solenoid sticking. That might explain why it works after you let it sit for 10 minutes. The solenoid gets hotter with use which causes the deteriorated foam on it to become sticky and hold down the release plate instead of letting it go. This allows the carousel to spin when it is supposed to stop for each color. The solenoid is located on the right side of the printer. If you open the lid, it is just behind the opening at the top right. You need to remove the top of the printer and scrape off the goo on top of the solenoid body. I put a piece of thin sticky backed felt to replace it. Other people use electrical tape.

Read Full Q/A … :

HP Color LaserJet 2550N

HP Color Laserjet blank pages – only jetdirect page

ANSWER : What about the engine test? To do that, drop down the front tray. Feel around on the left side at the top and you’ll feel a little plastic dongle. If you lift up on that it will initiate an engine test page. That will be a page containing lines of each color.

Read Full Q/A … :

HP Color LaserJet 2550N

evenly spaced horizontal lines on hp laserjet III printout

ANSWER : The lines would be a toner cartridge problem. Which paper tray? The MF tray or the optional paper cassette?

Read Full Q/A … :

HP Color LaserJet 2550N

HP Laserjet M3035xs RFU Upgrade

ANSWER : There’s no way.

Read Full Q/A … :

HP Color LaserJet 2550N

How to copy a card slot in HP laserjet 4250N

ANSWER : None that I know of, using a computer is likely your best option but I never attempted it.