HP Color LaserJet 5500

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Any of these error codes (51.2c , 51.2m , 51.2y , 51.2k) points to a failure with one of the laser scanner assemblies on the HP Color LaserJet 4600 series. To solve this error code, replace the corresponding laser scanner.
Most printers will stop working when they`re out of paper, ink or toner, or if the unit detects an issue with the ink or toner cartridge. When this occurs, you might receive an error message or notice blinking green or amber lights on your printer.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
This error is primarily caused by a transfer alienation failure in which the ITB is stuck and unable to rotate, the SR9 sensor (the primary transfer roller disengagement sensor) has gone bad or the fuser drive assembly has failed.
59.10 is a main drive error, which could be a bound up fuser. 51.10 is a laser error, which could be a bad laser unit. Which error do you have? If the printer can print an engine test, then you may have a bad formatter.
Common causes include dust and grime, worn rollers, or inappropriately weighted paper. Prevent paper jams by regularly cleaning your printer and replacing parts as needed. Check the weight of paper that your printer is rated for as well. The printed product is faded.
This error might display if the fuser temperature becomes too hot. Follow these steps to turn off the printer and allow the fuser to cool before printing again. Press the Power button to turn off the printer. Disconnect the power cord from the rear of the printer.
Select Start , then select Settings > Devices > Printers & scanners . Scroll down to Related Settings and select Print server properties. Select the Drivers tab, and see if your printer is listed. If it is, you`re all set.
On the control panel, open the Setup, Service, or Settings menu. Select Preferences, Printer Maintenance, or Tools. Select Web Services, Printer Update, or LaserJet Update. If prompted, follow the instructions to turn on Web Services.
The error code 0x0000002C, 0x00000000 typically occurs in systems where multiple AC feeds are powered on sequentially rather than simultaneously. An Onboard Administrator firmware update should remedy this problem.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
That error code indicates a failure of the yellow laser scanner. Unplug and leave for a few minutes, also make sure you are plugged directly into the wall and not into a surge protector.
If one or more toner cartridges are installed incorrectly, this may result in a 54.2 carousel rotation error. This error is typically accompanied by a loud grinding noise. NOTE: The carousel is the rotating part under the top cover to which all four print cartridges attach.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP Color Laserjet 3800 problem when printing color
ANSWER : Do a cold reset

Read Full Q/A … :

HP Color LaserJet 5500

HP Color Laserjet 2840 spitting out blanks
ANSWER : Moe- You are the man!

Read Full Q/A … :

HP Color LaserJet 5500

HP Color Laserjet blank pages – only jetdirect page
ANSWER : What about the engine test? To do that, drop down the front tray. Feel around on the left side at the top and you’ll feel a little plastic dongle. If you lift up on that it will initiate an engine test page. That will be a page containing lines of each color.

Read Full Q/A … :

HP Color LaserJet 5500

My 2550n Color LaserJet does not want to print in color
ANSWER : That model had issues with the carousel solenoid sticking. That might explain why it works after you let it sit for 10 minutes. The solenoid gets hotter with use which causes the deteriorated foam on it to become sticky and hold down the release plate instead of letting it go. This allows the carousel to spin when it is supposed to stop for each color. The solenoid is located on the right side of the printer. If you open the lid, it is just behind the opening at the top right. You need to remove the top of the printer and scrape off the goo on top of the solenoid body. I put a piece of thin sticky backed felt to replace it. Other people use electrical tape.

Read Full Q/A … :

HP Color LaserJet 5500

Reset HP Color Laserjet 4700 transfer kit
ANSWER : How about the situation when resistor does not reset the transfer belt count and even new transfer belt out of the box is not doing it. Do you have any idea how to solve this problem? I did reset transfer belts and fusing units on several HL 4700 printers with no problem but also I came across few which were not possible to reset even with oryginal parts.

Read Full Q/A … :

HP Color LaserJet 5500

HP Color LaserJet 4550 Streaking
ANSWER : hello,

Read Full Q/A … :

HP Color LaserJet 5500

HP Color LaserJet 4700
ANSWER : Saludos Amigo le Que le Pasa a tu Impresora Es Que Tienes rota El Sistema de sierre de la puerta con el Cierre de los tóner es Por Esa Razon Que No Cierra los tóner Si Quieres repararla Ponte en Contacto Madrid Seis Cinco Cinco Tres Cuarenta dos cuarenta y uno Reparación en el Momento saludos

Read Full Q/A … :

HP Color LaserJet 5500

HELP! HP Color Laserjet 5500dn (formatter prob??)
ANSWER : Italiano:

Read Full Q/A … :

HP Color LaserJet 5500