HP Color LaserJet 4500

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

On the printer control panel, press the Down Arrow to select Tools, and then press OK. Press the Down Arrow to select Clean Printhead, and then press OK. The printer cleans the printhead, and then prints a printhead test page. Review the print quality on the printhead test page.
If your HP printer not printing black ink correctly, here`s what you should do. Using non-genuine ink cartridges. Printheads that have become clogged. Ink cartridges that are defective or empty.
If one or more toner cartridges are installed incorrectly, this may result in a 54.2 carousel rotation error. This error is typically accompanied by a loud grinding noise. NOTE: The carousel is the rotating part under the top cover to which all four print cartridges attach.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
Check the ink levels

Sometimes, the printer may not print black ink because it is low or empty. You can check the ink levels on the printer`s display, or by using the software that came with your printer. If the ink level is low, replace the cartridge or refill it according to the manufacturer`s instructions.

The 59. F0 has been a common error code on the HP CLJ M452 and M377 / M477 MFP models. The printers service manual references this error to a “drum motor assembly” but in most cases has been resolved by replacing the Transfer Belt assembly (RM2-6454).
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
Turn the printer off then back on. If the issue persists, turn the printer off, unplug the power cord and then wait at least three minutes before plugging the power cord back in and turning the printer back on. If the issue persists, ensure the product is running the latest firmware available from HP.com.
note: Color calibration can be requested manually at any time from the front panel, by selecting the ink system icon , then going to Printhead management and selecting the option Calibrate color. caution: Color calibration can be performed successfully on opaque materials only.
Although different brands of cleaning solution will slightly vary when it comes to ingredients and ingredient ratios, they are largely based on the same three components: Distilled water. Isopropyl alcohol. Detergent.
Using an isopropyl alcohol dampened lint-free moist cloth, gently blot the nozzle plate until some ink is drawn out and absorbed into the cloth. Ensure rear electrical (gold) contacts are thoroughly clean of all ink residue and lint fibers. Ensure cartridge is dry before re-installing into printer.
This error message is usually the result of a cartridge that is not firmly seated in its designated slot. To troubleshoot the problem, begin by completely removing the cartridge from its port. Reinstall the cartridge by positioning it so that it snaps into place and is securely fastened in its slot.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP Color Laserjet 3800 problem when printing color
ANSWER : Do a cold reset

Read Full Q/A … :

HP Color LaserJet 4500

HP Color Laserjet 2840 spitting out blanks
ANSWER : Moe- You are the man!

Read Full Q/A … :

HP Color LaserJet 4500

HP Color Laserjet blank pages – only jetdirect page
ANSWER : What about the engine test? To do that, drop down the front tray. Feel around on the left side at the top and you’ll feel a little plastic dongle. If you lift up on that it will initiate an engine test page. That will be a page containing lines of each color.

Read Full Q/A … :

HP Color LaserJet 4500

My 2550n Color LaserJet does not want to print in color
ANSWER : That model had issues with the carousel solenoid sticking. That might explain why it works after you let it sit for 10 minutes. The solenoid gets hotter with use which causes the deteriorated foam on it to become sticky and hold down the release plate instead of letting it go. This allows the carousel to spin when it is supposed to stop for each color. The solenoid is located on the right side of the printer. If you open the lid, it is just behind the opening at the top right. You need to remove the top of the printer and scrape off the goo on top of the solenoid body. I put a piece of thin sticky backed felt to replace it. Other people use electrical tape.

Read Full Q/A … :

HP Color LaserJet 4500

HP Color LaserJet 4550 Streaking
ANSWER : hello,

Read Full Q/A … :

HP Color LaserJet 4500

Reset HP Color Laserjet 4700 transfer kit
ANSWER : How about the situation when resistor does not reset the transfer belt count and even new transfer belt out of the box is not doing it. Do you have any idea how to solve this problem? I did reset transfer belts and fusing units on several HL 4700 printers with no problem but also I came across few which were not possible to reset even with oryginal parts.

Read Full Q/A … :

HP Color LaserJet 4500

HP Color LaserJet 4700
ANSWER : Saludos Amigo le Que le Pasa a tu Impresora Es Que Tienes rota El Sistema de sierre de la puerta con el Cierre de los tóner es Por Esa Razon Que No Cierra los tóner Si Quieres repararla Ponte en Contacto Madrid Seis Cinco Cinco Tres Cuarenta dos cuarenta y uno Reparación en el Momento saludos

Read Full Q/A … :

HP Color LaserJet 4500

HELP! HP Color Laserjet 5500dn (formatter prob??)
ANSWER : Italiano:

Read Full Q/A … :

HP Color LaserJet 4500