HP DeskJet 950
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
The paper might not be engaged with the feed rollers. The paper-width guide is pressed against the paper stack too tightly. The paper tray is not completely inserted into the product. The paper settings in the print driver do not match the paper loaded in the paper tray.
When a new cartridge is installed it prints the calibration test page to check that it is aligned properly. With many HP printers you need to then scan the test page, so the printer can set itself up correctly.
Remove the dirt or dust from the paper rollers. Leave the rollers to dry for 10 minutes. ➔ Reconnect the cable, and power on the printer. You can also wipe the rollers using a soft cloth.
Several factors may cause the product to print blank pages, such as print settings, low ink, or the product itself. Check the following: Make sure the product is placed on a flat, stable surface that extends beyond the base in all directions. The product won`t operate properly if it`s tilted or at an angle.
There are numerous possible causes for a printer that`s randomly producing blanks. The most common ones are empty ink cartridges, improper cartridge installation, and congested nozzles. Driver and software issues can sometimes cause this problem as well.
If your printer is positioned far away from the network device, it may print more slowly. Especially wireless printing or if connected to an old fashioned `hub`. Speed things up by moving your printer closer to the router/switch/etc., or plug it directly into your primary switching.
The paper tray is empty or overloaded. The paper is curled. The print side, or shiny side, of the paper is not loaded in the paper tray face up. For photo paper, always load the rougher side of the paper facing down.
There are a few things that could be the cause of this problem, including: Empty ink or toner cartridges that need replacing. Ink or toner cartridges that have become dislodged from their proper place. The wrong paper size loaded in the input tray.
With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.
Select Start , then select Settings > Devices > Printers & scanners . Scroll down to Related Settings and select Print server properties. Select the Drivers tab, and see if your printer is listed. If it is, you`re all set.
Issues in your printer`s ink or toner cartridges as well as an empty paper tray can cause your printer to delay your prints. Make sure that your cartridges are not running out of ink and the paper tray is not empty. You can follow HP`s guide on how to check ink or toner levels here.
By spooling the documents, the program dumps the print job into the spooler. This only takes a few seconds. After which, the computer considers it done and frees up some memory.
Volatile memory requires power to store the information. Deleting volatile memory is easy: Simply shut down or unplug your printer for a minute or so. Most printers also have non-volatile memory (a hard drive) that is stored until you physically delete it.
How to Manually Stop and Start the Print Spooler. Click the Start button and select Run. Type Command (Figure 1 [English only]) and then click OK to display the Command Prompt (Figure 2 [English only]). In the Command Prompt type, net stop spooler, then press Enter to Stop the Print Spooler.
Print Spooler background
The Print Spooler service is required when a computer is physically connected to a printer that provides printing services to additional computers on the network.
Paper pushed too far into the input tray when it is loaded, might feed into the printer incorrectly, causing the paper to tear. Paper stacks loaded into the input tray with too many or too few sheets of paper, might feed into the printer incorrectly, causing the paper to tear.
The paper has holes along both sides that fit over the sprockets located on the feeder wheel. When the wheel turns, it feeds the paper into the printer. The holes are torn off the paper after the printout is complete. And, yes, printers still use this type of feeder mechanism.
The optical sensor reads the unique media `signature` of the paper by measuring inherent optical properties and comparing them with the signatures of other papers. Once the paper is identified, the printer optimizes printing for the particular paper type.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
Run Diagnose & Fix
Open the HP Smart app, and then open Diagnose & Fix. Windows: Click the Diagnose & Fix icon in the bottom left corner. macOS: Click your printer, click Printers in the top menu bar, and then click Diagnose & Fix.
The warranty period for the printheads is 1000 cc of ink through the printhead (previously 700 cc), or the expiration date printed on the printhead, whichever comes first. However, printheads may last much longer than 1000 cc of ink. On average, printheads should last through 2-3 ink cartridges.
The print head cleaning function allows you to clear up clogged print head nozzle. Perform print head cleaning if printing is faint or a specific color fails to print, even though there is enough ink.
The nozzle check function allows you to check whether the print head is working properly by printing a nozzle check pattern. Print the pattern if printing becomes faint, or if a specific color fails to print.
Separator pages are pages that print at the beginning of the printed output. Separator pages for print jobs (job separators) are specified by the SEPPAGE parameter on the output queue.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.
Read Full Q/A … :
HP DeskJet 950
hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.
Read Full Q/A … :
HP DeskJet 950
HP PSC 950 All in one Printer
ANSWER : Just leaf through our prearranged folder and find a HP PSC 950xi All-in-One Printer driver that need someone to write my college essay fits your requirements.
Read Full Q/A … :
HP DeskJet 950
HP DeskJet 722C Paper Feed Problem
ANSWER : Detach the force string from the holding nothing back one and expel all paper from it.
Read Full Q/A … :
HP DeskJet 950
HP 4250n 41.3 unexpected paper size
ANSWER : BULLSHIT
Read Full Q/A … :
HP DeskJet 950
Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.
Read Full Q/A … :
HP DeskJet 950
HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr
Read Full Q/A … :
HP DeskJet 950
HP 4250 13.06.00 Fuser output paper stop !
ANSWER : pick up solenoid
Read Full Q/A … :
HP DeskJet 950