HP DeskJet 932C

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

1. Causes of Multiple Sheet Feed. Multiple pages being fed through the printer overlapping or in a stack occurs when the media fails to separate correctly in the tray. Common causes are issues with the print media, incorrectly adjusted paper trays and worn or contaminated feed or separator rollers.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust.
Right Click on the Printer Icon in “Devices & Printers, then click on “Device Settings”, scroll down to “Installable Options” and then disable “Mopier Mode”.
Usually this issue occurs if there is any file missing or corrupted in the Printer drivers/print spooler.
On your PC search control panel, open control panel, Select printer properties, Select the “number of copies” it must be set to 2 change it to 1 and check if it helps. If the issue still persists uninstall the printer software from your PC and install the latest printer drivers.
What should a technician do if a printer is feeding two pieces of paper instead of one for every page printed? Inspect for worn feed rollers. What type of printer is the fastest?
A printer printing lines on the page are normally caused by a blocked, dirty, or damaged print head. Blocked ink cartridge nozzles, or not removing protective seals correctly when you installed a new ink cartridge can also cause missing lines of print.
Dust, paper fiber, and other debris might accumulate on the pick rollers and cause paper feed issues. To help prevent paper feed issues, clean the rollers inside the printer and in the duplexer (if equipped). If the other steps in this document fail to resolve the issue, then reset the printer.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
The paper feeding mechanism includes a drive gear coaxially coupled to a shaft of drive roller for transferring a sheet to a printing zone, a feed gear coaxially coupled to a shaft of the feed roller and operating to align the sheet transferred from the drive roller, and a discharge gear coaxially coupled to a shaft of …
Create custom paper sizes in printer properties (Windows)

In the Print window, click Preferences, Properties, or Printer Properties. Click the Paper/Quality tab, and then click Custom. Click New, type a name for the custom paper size, select the width and height, and then click OK to save the paper.

Misfeeds occur frequently. The number of sheets loaded exceeds the capacity of the printer. Load paper only as high as the upper limit markings on the side fences of the paper tray, or the markings on the paper guides of the bypass tray.
Mopier refers to a type of mode that computer printers may be switched on to that only allows them to print one copy of a document at a time. This mode must be disabled if someone wants to print multiple copies of a document.
Double printing can occur for several possible reasons including an improperly seated ink tank, a misaligned print head, and a dirty encoder stip.
Adjust the print settings: Check your printer`s settings to make sure it`s not set to print multiple copies or double-sided printing. Update or reinstall the printer drivers: Outdated or corrupted drivers can cause printing issues.
There are a few things that could be the cause of this problem, including: Empty ink or toner cartridges that need replacing. Ink or toner cartridges that have become dislodged from their proper place. The wrong paper size loaded in the input tray.
The monthly duty cycle limit is 30,000 pages, with a recommended monthly duty cycle of 500 to 3500 pages. The sort of print job you`re running can be very stressful on the printer; I`d suggest that you allow the printer to cool down for 10-15 minutes every 500 or so pages.
The streaks or lines might be caused due to low ink levels in one or both ink cartridges. Check the ink levels using the HP Toolbox to determine if the ink cartridges are low on ink and need to be replaced. note: Ink level warnings and indicators provide estimates for planning purposes only.
Make sure that your page settings are set to print all pages and to print every page. Settings that cause some pages not to print are `manual duplexing`, `print every other page`, `print odd pages`, `print on both sides`, or similar settings.
Using both hands, put one piece of paper in the manual feed slot until the front edge of the paper touches the paper feed roller. Once the machine has grasped the paper, let go. The side to be printed should be faced up. The machine will hold the paper in place until the print data is sent to the machine.
Pour 1 tbsp. of isopropyl alcohol or clean water onto a lint-free cloth and scrub the paper or internal tray rollers with the cloth. Fold the cloth in half and repeat the cleaning process until the rollers are free of dust and debris. Wipe the rollers with a dry, lint-free cloth to remove any remaining dust or debris.
1. or feed roller : a roll or one of two or more rolls by which material is drawn or fed into a machine. 2. : one of a set of small rubber rolls under the platen of a typewriter that help to roll the paper and hold it in place during typing.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
1. On the printer display home screen, select the “set up” button (it looks like a gear). 2. Select “settings” > “device settings” > “reset settings” > “reset all” > “OK” and then “Yes.”

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

HP DeskJet 932C

HP DeskJet 722C Paper Feed Problem
ANSWER : Detach the force string from the holding nothing back one and expel all paper from it.

Read Full Q/A … :

HP DeskJet 932C

Paper Feed Problem on HP R80
ANSWER : In the last examination it is our origination of death which chooses our responses to all the inquiries life puts to us. The most pleasant spot to be is in somebody’s idea; the most secure spot to be is in somebody’s petitions.

Read Full Q/A … :

HP DeskJet 932C

HP 1220C Photo Paper Feed Problems
ANSWER : This problem isn’t about the paper picker. Here is the real issue and fix:

Read Full Q/A … :

HP DeskJet 932C

leaking hp 932c
ANSWER : same with my hp deskjet 960c

Read Full Q/A … :

HP DeskJet 932C

HP laserjet 3100 multiple page feed fixed!
ANSWER : Can you tell me what kit you are referring to because I have the exact problem with my 3100 printer?

Read Full Q/A … :

HP DeskJet 932C

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :

HP DeskJet 932C

Tray 1 (upper tray) paper feed problem
ANSWER : There is no way of adjusting the distance of lift. Could be that the pickup roller is worn enough that it will pick up a sheet that is higher, but not one that is lower down. You can look at the end of the roller that first makes contact and see if it is worn smooth.

Read Full Q/A … :

HP DeskJet 932C