HP LaserJet 8000N

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary. Then reload the paper. If thick media does not feed, make sure you are loading it straight into the product, not at an angle. If paper jams when you print on both sides of the paper, try loading fewer sheets.
The common reasons for this issue are various, for instance, the paper input tray is overloaded, dust or moisture can affect the paper feed or paper pick rollers, the printer driver is old, etc. Thus, the printer cannot detect the paper that has been inserted into the tray.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust.
Dust, paper fiber, and other debris might accumulate on the pick rollers and cause paper feed issues. To help prevent paper feed issues, clean the rollers inside the printer and in the duplexer (if equipped). If the other steps in this document fail to resolve the issue, then reset the printer.
Adjust the paper guides in the tray to match the size of the paper. Remove the paper, smooth it out, then reload it. If the paper misfeeds, do not use that paper. Remove the moist paper, then replace it with new, dry paper.
There are different methods of paper feeding. With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.
Click: `Open the HP Photosmart Toolbox` or: `Service this device` Click: Device Services tab. Click: Calibrate the Device or Clean the Print Cartridges or Align the printer. Follow the instruction which will appear on-screen.
Depending on the setting, printed copies are fed as follows: Side 1 is the surface of the paper printed during one-sided printing, or the surface of the first print during duplex printing. Side 2 is the surface of the paper printed on the back side of Side 1 during duplex printing.
Continuous form feed and friction feed are the two types of paper feeder mechanisms. Dot matrix printers use continuous form feed, and laser printers use friction feed.
Misfeeds occur frequently. The number of sheets loaded exceeds the capacity of the printer. Load paper only as high as the upper limit markings on the side fences of the paper tray, or the markings on the paper guides of the bypass tray. Misfeeds occur frequently.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer. False paper jams can also occur.
Overfilling the paper tray is frequently causes paper jams. Many printers have sliding mechanisms that allow different types and sizes of paper to be fed into the printer. If the slider is not correctly positioned, it can cause a paper jam. Use standard office paper.
This is often caused by the fact the pick-up roller is worn out. The layer of rubber around this plastic part overtime gets too smooth, preventing paper from feeding properly into the printer. This fix is not really hard, will take no more than half an hour and costs around 10,- (Euro or Dollar).
a device for inserting sheets of paper into a printer or typewriter.
The paper feed is from the front.
The manual feed slot is located on the front of your printer. It can be closed when not in use, making the product more compact.
The Manual Feed message appears when Manual is chosen as the paper source in the printer driver and there is no paper in the manual feed slot.
The streaks or lines might be caused due to low ink levels in one or both ink cartridges. Check the ink levels using the HP Toolbox to determine if the ink cartridges are low on ink and need to be replaced. note: Ink level warnings and indicators provide estimates for planning purposes only.
This is often caused by the fact the pick-up roller is worn out. The layer of rubber around this plastic part overtime gets too smooth, preventing paper from feeding properly into the printer. This fix is not really hard, will take no more than half an hour and costs around 10,- (Euro or Dollar).
Common factors include driver problems, software issues, hardware failures and overuse.
A Printer Failure. There is a problem with the printer or ink system. Turn printer off, then on. If problem persists, contact HP. error message displays on the printer control panel, and the printer does not print.
This is often caused by the fact the pick-up roller is worn out. The layer of rubber around this plastic part overtime gets too smooth, preventing paper from feeding properly into the printer. This fix is not really hard, will take no more than half an hour and costs around 10,- (Euro or Dollar).

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Paper Feed Problem on HP R80
ANSWER : In the last examination it is our origination of death which chooses our responses to all the inquiries life puts to us. The most pleasant spot to be is in somebody’s idea; the most secure spot to be is in somebody’s petitions.

Read Full Q/A … :

HP LaserJet 8000N

HP 1220C Photo Paper Feed Problems
ANSWER : This problem isn’t about the paper picker. Here is the real issue and fix:

Read Full Q/A … :

HP LaserJet 8000N

HP DeskJet 722C Paper Feed Problem
ANSWER : Detach the force string from the holding nothing back one and expel all paper from it.

Read Full Q/A … :

HP LaserJet 8000N

HP Officejet 7310 problem
ANSWER : My HP Officejet7310xi All-in-One has an error message 0x886a789a on a blue screen, with Auto Answer, !, and Power (Print On) flashing. What does this indicate?

Read Full Q/A … :

HP LaserJet 8000N

HP PSC 1610 – problem installing hardware
ANSWER : If you want to get proper detailed information about hp printer then you should call on 1-888-924-2961 toll free number. They provide you step by step methods of installation process and driver support services.

Read Full Q/A … :

HP LaserJet 8000N

HP PSC 1510 copying problems
ANSWER : my hp photocopy is not working

Read Full Q/A … :

HP LaserJet 8000N

HP DeskJet 510 – problem
ANSWER : Recently started to look for a trusted and high-quality work with a broker for binary options, but the search was not a very successful, and my friend who is already a few years makes this kind of activity offered me options brokers review – site who himself uses optionsbrokersreview.com

Read Full Q/A … :

HP LaserJet 8000N

HP LaserJet 1160 pick-up problem
ANSWER : Take the black rubber roller out. Clean it and turn it 90-180 degrees so there is fresh rubber in the “corner”.

Read Full Q/A … :

HP LaserJet 8000N